1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    Im very sorry for the late reply! I totally forgot about this thread. The R1 is still working perfectly. I fixed the issue by installing new...
    Post by: Matthew Bartlett, Jul 6, 2017 in forum: Troubleshooting
  2. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Well, thank you all for helping! I think I have solved the problem. There was nothing wiring with the drivers, or the wiring, or the printer...
    Post by: Matthew Bartlett, Sep 15, 2016 in forum: Troubleshooting
  3. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Do you think it may be a mistuned stepper driver?
    Post by: Matthew Bartlett, Sep 14, 2016 in forum: Troubleshooting
  4. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Ok, I'll check it when I have time, I'm also planning on having a Skype meeting with a technician
    Post by: Matthew Bartlett, Sep 12, 2016 in forum: Troubleshooting
  5. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Well, the wiring doesn't seem to have any problems. I checked by the stepper and the board, and I don't see any problem. I talked to tech support...
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Troubleshooting
  6. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    OK, i'll check the wiring. I'll keep you updated.
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Troubleshooting
  7. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    I usually use mattercontrol, but I tried Cura and I get the same result.
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Troubleshooting
  8. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Well, during printing the axis keep moving, but the extruder motor just stops moving. It is still locked, but it doesn't turn.
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Troubleshooting
  9. Matthew Bartlett
    Post

    Solved Well, Just when I thought it was all over...

    Well, I was playing around with the printer and found that the extruder can run when it is not doing a print. But when it is doing a print, it...
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Troubleshooting
  10. Matthew Bartlett
    Thread

    Solved Well, Just when I thought it was all over...

    Well, I've had a few problems with my printer so far. But this one frustrates me greatly. As I start a print, the heater on the extruder and bed...
    Thread by: Matthew Bartlett, Sep 10, 2016, 15 replies, in forum: Troubleshooting
  11. Matthew Bartlett
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    SO, with this mod, can you still reinstall the top cover?
    Post by: Matthew Bartlett, Sep 10, 2016 in forum: Mods and Upgrades
  12. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    Thank you very much! I will look into the alternatives. I will keep you updated.
    Post by: Matthew Bartlett, Sep 9, 2016 in forum: Troubleshooting
  13. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    Where can I get the upgrade at besides Robo 3d? Is it possible to get it elsewhere?
    Post by: Matthew Bartlett, Sep 9, 2016 in forum: Troubleshooting
  14. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    OK, I'll try and buy it, If I can find a place to get it at considering that it's sold out on the robo page.
    Post by: Matthew Bartlett, Sep 9, 2016 in forum: Troubleshooting
  15. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    It works on the original too right?
    Post by: Matthew Bartlett, Sep 8, 2016 in forum: Troubleshooting
  16. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    I was just concerned that the bracket that held the bolts and switches was not included, and where to print it. So, mind me asking but, what was...
    Post by: Matthew Bartlett, Sep 8, 2016 in forum: Troubleshooting
  17. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    I have heard of the motors with the Z axis screws built in, but I'm not sure what mods I'll have to make to the Switches of the Z axis, and the...
    Post by: Matthew Bartlett, Sep 8, 2016 in forum: Troubleshooting
  18. Matthew Bartlett
    Post

    Solved PLS Help! Print quality suffers!!!

    It is the original R1, PLA+ABS model. there are the lead screw couplers at the bottom, yes. However I have already tried tightening them, and...
    Post by: Matthew Bartlett, Sep 8, 2016 in forum: Troubleshooting
  19. Matthew Bartlett
    Thread

    Solved PLS Help! Print quality suffers!!!

    Hello! I have had my robo r1 for about a month now, and I love it a lot! But, there is a problem. This. There is major artifacting on the print....
    Thread by: Matthew Bartlett, Sep 8, 2016, 14 replies, in forum: Troubleshooting
Showing results 1 to 19 of 19
Search Again