1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. twilk53
    Post

    Solved No auto leveling

    It worked! Thanks. I should have said there is a place in Cura instead of Octoprint to put in commands to perform before the print starts. Somehow...
    Post by: twilk53, May 21, 2017 in forum: Troubleshooting
  2. twilk53
    Post

    Solved No auto leveling

    Thank you. I will try that. There is a place in Octoprint to put in commands that are to be done before any print starts. Seems like a good place...
    Post by: twilk53, May 19, 2017 in forum: Troubleshooting
  3. twilk53
    Thread

    Solved No auto leveling

    After having a problem where my printer doesn't auto level or check the z height on new prints, I re-installed Mattercontrol, got a new laptop,...
    Thread by: twilk53, May 18, 2017, 4 replies, in forum: Troubleshooting
  4. twilk53
    Post

    Solved Matterhacker problem

    Thanks.
    Post by: twilk53, Apr 30, 2017 in forum: Troubleshooting
  5. twilk53
    Post

    Solved Matterhacker problem

    I've never heard of Win32DiskImager but I'm willing to try to learn it. I went looking on Amazon for Pi kits and rather than buying the most...
    Post by: twilk53, Apr 29, 2017 in forum: Troubleshooting
  6. twilk53
    Post

    Solved Matterhacker problem

    I paid $200 for a refurbished unit and I'm very sorry I did. I've used Octoprint and Raspberry Pi where I just retired from and loved it. It was...
    Post by: twilk53, Apr 27, 2017 in forum: Troubleshooting
  7. twilk53
    Thread

    Solved Matterhacker problem

    I'm suddenly having all kinds of software problems. Old g codes work fine. Anything new misses the first two or three layers and has a rough final...
    Thread by: twilk53, Apr 26, 2017, 11 replies, in forum: Troubleshooting
  8. twilk53
    Thread

    Solved Clogged extruder

    My extruder is clogged and I need to remove either the tip or the whole hot end to get it cleared. How do I go about this?
    Thread by: twilk53, Nov 26, 2016, 14 replies, in forum: Troubleshooting
  9. twilk53
    Post

    Unresolved Z height problem?

    Whatever the default is.
    Post by: twilk53, Sep 14, 2016 in forum: Troubleshooting
  10. twilk53
    Post

    Unresolved Can't print from SD card

    1.5
    Post by: twilk53, Sep 14, 2016 in forum: Troubleshooting
  11. twilk53
    Thread

    Unresolved Z height problem?

    I have been using blue painters tape to help with adhesion to the bed (sometimes it works too well). The last couple of prints I've noticed that...
    Thread by: twilk53, Sep 14, 2016, 3 replies, in forum: Troubleshooting
  12. twilk53
    Post

    Unresolved Can't print from SD card

    I just figured out what I have been doing wrong. I have been clicking on "disconnect" and the software warns me that disconnecting will end the...
    Post by: twilk53, Sep 14, 2016 in forum: Troubleshooting
  13. twilk53
    Post

    Unresolved Can't print from SD card

    I am having the same problem. Its almost as if the printer can't see the sd card.
    Post by: twilk53, Sep 13, 2016 in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again