1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 4
  1. Allelujah
    Post

    Solved Unidentified Part?

    Alrighty thanks guys. Is there really no need for it? Will it be safe to continue printing without it?
    Post by: Allelujah, Sep 9, 2018 in forum: Troubleshooting
  2. Allelujah
    Thread

    Solved Unidentified Part?

    Hello everyone. Its been about a year or two since i last been on the forums. So I been enjoying my Robo R1+ for the past 2 years now and I was...
    Thread by: Allelujah, Sep 8, 2018, 7 replies, in forum: Troubleshooting
  3. Allelujah
    Post

    Answered Nozzle Replacement

    Thanks XD I plan on printting some very small details for my Gunpla Swords So i hope it does just that :D. Also bought a .25 and a .8 nozzle. The...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  4. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty. That sounds like a problem for future self to deal with tomorrow. Thanks for the help and advice Mark.
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  5. Allelujah
    Post

    Answered Nozzle Replacement

    OK so thats 2 things i should change, what should I change them to? Or is that something i need to ask somewhere else? I assume there is a long...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  6. Allelujah
    Post

    Answered Nozzle Replacement

    Yeah I went from the normal default nozzle size to a 0.15 And I think I found where i need to make changes but not sure if there is anywhere else...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  7. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty. Also I know there is someone on the forums that uses Matter Control as well but his name escapes me, I hope he looks at this thread...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  8. Allelujah
    Post

    Answered Nozzle Replacement

    Does the shaft part of the nozzle need to be fully in the block part of the hot end? Beacause I do not have the hex part of the Nozzle touching...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  9. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty lol I have a pliers and a wrench would that work? Dont have 2 wrenches unfortunately
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  10. Allelujah
    Post

    Answered Nozzle Replacement

    Alrighty I will try and watch the vid. I am mostly deaf so hearing what the person says will be an issue if he says something important. I will...
    Post by: Allelujah, Feb 4, 2017 in forum: General Questions
  11. Allelujah
    Thread

    Answered Nozzle Replacement

    Hello everyone, I am back yet again with another few questions. So my new nozzles came in the mail today and I am eagerly waiting to install one...
    Thread by: Allelujah, Feb 4, 2017, 20 replies, in forum: General Questions
  12. Allelujah
    Thread

    Solved Types of Filament

    Hello everyone. Got another question for you all. Well a couple questions. First up is what are all the different types of filament can the Robo...
    Thread by: Allelujah, Jan 7, 2017, 2 replies, in forum: General Questions
  13. Allelujah
    Post

    Smallest Detail

    Yeah i never heated it the firs ttime i removed it and put it back on.... So I think that was my first mistake, the second mistake was tightening...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  14. Allelujah
    Post

    Smallest Detail

    So i have another question but this time about how to remove a nozzle that is on really tight. I dont want to strip it and or break anything...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  15. Allelujah
    Post

    Smallest Detail

    Yeah Im thinking about getting a variety of nozzles since from what i have read is some prints will require certain nozzles XD I plan on 3D...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  16. Allelujah
    Post

    Smallest Detail

    Alrighty thanks XD I will shop around and see where i can get the best price. And will do to avoid volcano nozzles lol
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  17. Allelujah
    Post

    Smallest Detail

    Great lol well Does Robo 3D sell different nozzles or where would I go to get other nozzles? And is it a good idea to have a few nozzles laying...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  18. Allelujah
    Post

    Smallest Detail

    Alrighty XD Thanks for the replies :D Going to get back into Fusion 360 and rework these designs.
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  19. Allelujah
    Post

    Smallest Detail

    Do you think I should try a print with roughly the same level of detailing or should i make sure my angles and lines are around 1mm and over?...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
  20. Allelujah
    Post

    Smallest Detail

    Not sure what the Nozzle diameter is on my Robo R1+ XD Its stock with whatever it came with. But I am guessing that its not small enough for the...
    Post by: Allelujah, Jan 1, 2017 in forum: General Questions
Showing results 1 to 20 of 70 Next >
Search Again
Page 1 of 4