1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Ed Ferguson
    Thread

    Can't remove quick release plate pivot screw. Ideas?

    I'm upgrading to a E3Dv6 hot end on my son's R1+. Printed a new quick release plate off Thingiverse, but I can't get the old plastic quick...
    Thread by: Ed Ferguson, Dec 22, 2018, 6 replies, in forum: Mods and Upgrades
  2. Ed Ferguson
    Thread

    Unresolved R1+ Z Offset Concern

    I installed Marlin 1.1.5 on my Robo R1+. I set it up for MESH_BED_LEVELING and it prints a 20mm cube fine. I have not created the Mesh yet, as I...
    Thread by: Ed Ferguson, Sep 6, 2017, 1 replies, in forum: Troubleshooting
  3. Ed Ferguson
    Thread

    OctoPrint IP Address keeps changing

    My OctoPrint IP Address keeps changing. Sometimes it's 192.168.1.15, other times I start the printer it's 192.168.1.14 for example. Drives me...
    Thread by: Ed Ferguson, Jun 28, 2017, 15 replies, in forum: Software
  4. Ed Ferguson
    Thread

    Marvin on the R2

    Marvin from Thingiverse printed on the Robo R2 at 0.2mm layer height. MakerGeeks silver PLA. Sliced with Simplify 3D. [ATTACH] [ATTACH]
    Thread by: Ed Ferguson, Jun 27, 2017, 3 replies, in forum: Show and Tell
  5. Ed Ferguson
    Thread

    Register your R2 Warranty Online

    Don't forget to register your R2 warranty online at: https://robo3d.com/register/ I believe under US law a company can't deny warranty because...
    Thread by: Ed Ferguson, Jun 19, 2017, 5 replies, in forum: General Questions
  6. Ed Ferguson
    Thread

    R2 Stylus Holder

    R2 Stylus Holder Pclabtech designed an LCD stylus holder that snaps over the Robo R2 metal door handle....
    Thread by: Ed Ferguson, Jun 16, 2017, 3 replies, in forum: Show and Tell
  7. Ed Ferguson
    Thread

    3DSolutech PLA - Any experience?

    Want to try some PLA from 3DSolutech after reading a guy on 3D Hubs rave about it. They are located 30 miles from me in Seattle, which is a bonus...
    Thread by: Ed Ferguson, Jun 13, 2017, 5 replies, in forum: Filament
  8. Ed Ferguson
    Thread

    Robo R2 Calibration Cube

    Robo R2 Calibration Cube with small radius edges. 20mm cube. 0.1mm layer height. Robo PLA. Sliced with Simplify3D. [ATTACH]
    Thread by: Ed Ferguson, Jun 9, 2017, 15 replies, in forum: Show and Tell
  9. Ed Ferguson
    Thread

    Robo R2 Overhang Tests

    Made these Robo R2 overhang prints at 0.1mm layer height using Robo PLA and sliced on Simplify3D. The print on the right was just under 10 hours....
    Thread by: Ed Ferguson, Jun 9, 2017, 10 replies, in forum: Show and Tell
  10. Ed Ferguson
    Thread

    Benchy on Robo R2 sliced with Simplify3D

    [ATTACH] Benchy on Robo R2 sliced with Simplify3D For those new to 3D printing, the model "Benchy" is commonly used as a benchmark torture test....
    Thread by: Ed Ferguson, Jun 3, 2017, 11 replies, in forum: Show and Tell
  11. Ed Ferguson
    Thread

    R2 Heated Bed Design

    I’ve not seen any detail photos of the removable R2 heated bed – so I took photos. The Z platform base is metal with a plastic cross member frame...
    Thread by: Ed Ferguson, Jun 1, 2017, 28 replies, in forum: Show and Tell
  12. Ed Ferguson
    Thread

    Robo R2 First Print – The Good, the Bad, and the Funny

    Received my Robo R2 today ($1,000 early backer on Kickstarter). For background, I’ve been using my son’s Robo R1+ extensively for 8 months. The...
    Thread by: Ed Ferguson, Jun 1, 2017, 8 replies, in forum: Show and Tell
  13. Ed Ferguson
    Thread

    Video of Robo C2 and R2 in action at the Microsoft Store

    Video of Robo C2 and R2 in action at the Microsoft Store [MEDIA] BTW - The Robo C2 is now available through the online Microsoft store:...
    Thread by: Ed Ferguson, May 28, 2017, 4 replies, in forum: Show and Tell
  14. Ed Ferguson
    Thread

    Video review of Robo C2

    Video review of Robo C2 [MEDIA]
    Thread by: Ed Ferguson, Feb 2, 2017, 8 replies, in forum: General Questions
  15. Ed Ferguson
    Thread

    Robo 3D and Foxconn sign manufacturing agreement

    Robo 3D and Foxconn sign manufacturing agreement...
    Thread by: Ed Ferguson, Jan 16, 2017, 1 replies, in forum: Show and Tell
  16. Ed Ferguson
    Thread

    Video of Robo C2 / Amazon Echo voice control

    Video of Robo C2 / Amazon Echo voice control https://www.kickstarter.com/projects/1238702276/robo-c2-and-robo-r2-smart-3d-printers/posts/1740874
    Thread by: Ed Ferguson, Nov 19, 2016, 20 replies, in forum: Show and Tell
  17. Ed Ferguson
    Thread

    Robo C2 Production Line Photos

    Latest Kickstarter Robo C2 update with production line photos just got posted:...
    Thread by: Ed Ferguson, Nov 4, 2016, 0 replies, in forum: Show and Tell
  18. Ed Ferguson
    Thread

    Explosion caused by 3D printer and hairspray kills teenage boy

    Explosion caused by 3D printer and hairspray kills teenage boy...
    Thread by: Ed Ferguson, Nov 3, 2016, 5 replies, in forum: General Questions
  19. Ed Ferguson
    Thread

    Cura Users - Which version are you using?

    I'm curious which version of Cura Robo 3D users like best. I downloaded and tested the latest (ver 2.3 Oct 2016), but my son says it seems like a...
    Thread by: Ed Ferguson, Nov 3, 2016, 5 replies, in forum: Software
Showing results 1 to 19 of 19
Search Again