1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    You need to add this library go to sketch include library manage libraries and then search for U8G
    Post by: crombiecrunch, Mar 3, 2017 in forum: Mods and Upgrades
  2. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I have #define RGB_LED #if ENABLED(RGB_LED) #define RGB_LED_RED_PIN 5 #define RGB_LED_GREEN_PIN 4 #define RGB_LED_BLUE_PIN 6 #endif and...
    Post by: crombiecrunch, Mar 3, 2017 in forum: Mods and Upgrades
  3. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    can someone tell me what I need to do to get the temp status lights working on this firmware? I get the error of #error "TEMP_STAT_LEDS requires...
    Post by: crombiecrunch, Mar 3, 2017 in forum: Mods and Upgrades
  4. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Im having a couple of issues. 1 when heating the extruder, if i have the temp set to say 240, it will heat up to past 250 and then drop to 230...
    Post by: crombiecrunch, Mar 3, 2017 in forum: Mods and Upgrades
  5. crombiecrunch
    Post

    RGB LED Wiring Diagram and Code

    has anyone gotten this to work with Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)?
    Post by: crombiecrunch, Mar 1, 2017 in forum: Mods and Upgrades
  6. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Lol so after all that. I had to go back to stock firmware until I figure all this out. I tried printing sokething and the layers where paper...
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  7. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Thanks all, yes I have a lot of reading to do. LOL
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  8. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I really appreciate all the help @danzca6 Can you tell me what the difference is between the ABL and MESH versions? Im doing a test print now and...
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  9. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    yes so I take it i need to change something somewhere hahahahaha
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  10. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    ok so you can tell how damn new I am to this. I have a Robo R1 Plus and I downloaded the RCBF_ABL_Plus_10-15 files and uploaded them. After it it...
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  11. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    thanks thats what I was looking for. Should I see it do anything after I send the commands? My screen just stays at start echo:Marlin1.0.0 echo:...
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  12. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Sorry I should have asked better, where or how do I enter those codes?
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
  13. crombiecrunch
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Hello all new printer user here and still learning the ropes, how do I :clear EEPROM memory by issuing the following two commands in terminal...
    Post by: crombiecrunch, Nov 2, 2016 in forum: Mods and Upgrades
Showing results 1 to 13 of 13
Search Again