1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. CDitty
    Thread

    Solved Print shifting

    I have had this happen twice now and can't figure out why. For some reason, my print is shifting. When I look at the print in octoprint, layer...
    Thread by: CDitty, Oct 17, 2017, 21 replies, in forum: Troubleshooting
  2. CDitty
    Thread

    Solved Poor quality print quality lately

    For some reason, some of my latest prints have been poor quality. Parts of the print look sloppy or not as sharp as the part next to it or the...
    Thread by: CDitty, Jan 26, 2017, 4 replies, in forum: Troubleshooting
  3. CDitty
    Thread

    Solved Grinding noises on print start

    I added a camera mount to my print bed the other day and now everytime that I print, it sounds like the gears are grinding. I checked the belt...
    Thread by: CDitty, Jan 23, 2017, 3 replies, in forum: Troubleshooting
  4. CDitty
    Thread

    Print head and cables

    I had to replace my temp lead wire a few weeks ago and since then, I swear the hothead isn't positioned in the right orientation. It looks like...
    Thread by: CDitty, Jan 10, 2017, 0 replies, in forum: General Questions
  5. CDitty
    Thread

    Solved Acetone & PLA

    Isn't acetone supposed to melt PLA? I saw a video where the guy took his excess PLA from prints and made a sludge from it for better bed...
    Thread by: CDitty, Jan 4, 2017, 14 replies, in forum: General Questions
  6. CDitty
    Thread

    OctoPrint & Cura - Printhead too high on prints....

    As you can see from the my recent forum posts, I've been playing with OctoPrint and various slicers. Somehow, during all that messing around, I...
    Thread by: CDitty, Dec 29, 2016, 12 replies, in forum: Software
  7. CDitty
    Thread

    OctoPrint 1.3 - staying connected

    I have my octoPrint setup and working (mostly), but it seems to be having a connectivity issue after about an hr or so. I'm curious to know what...
    Thread by: CDitty, Dec 28, 2016, 3 replies, in forum: Software
  8. CDitty
    Thread

    Setting up other slicers & octoprint

    I am in the process of playing with various slicers and trying to get my octoprint working correctly. I've noticed that each slicer has a section...
    Thread by: CDitty, Dec 28, 2016, 2 replies, in forum: Software
  9. CDitty
    Thread

    Solved Filament stuck in printhead

    I have a piece of filament stuck just under the gear in the print head. Are there any idiot proof instructions on how to take the printhead apart...
    Thread by: CDitty, Dec 24, 2016, 3 replies, in forum: Troubleshooting
  10. CDitty
    Thread

    Printing multiple items and one messes up

    If I am printing multiple items and one of the items starts to mess up to the point it could jeopardize the rest of the prints, is there a way to...
    Thread by: CDitty, Dec 24, 2016, 3 replies, in forum: General Questions
  11. CDitty
    Thread

    Solved Making the bed sticky - Thoughts?

    Hi all. I'm curious about how everyone makes their print bed sticky. On my last little cheapy 3d printer, the bed was plastic and the printer...
    Thread by: CDitty, Dec 15, 2016, 12 replies, in forum: General Questions
  12. CDitty
    Thread

    Solved Cleaning the print bed

    I just got my Robo3D yest and went the glue stick route for my first couple of prints. I think I am going to switch to using hairspray. How does...
    Thread by: CDitty, Dec 14, 2016, 13 replies, in forum: General Questions
Showing results 1 to 12 of 12
Search Again