1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jeff Meador
    Post

    Solved New R1+ Not Autoleveling correctly

    I figured it out: the person who assembled it switched the wiring around on the sensors on the left side. Not too happy with Robo on some shoddy...
    Post by: Jeff Meador, May 5, 2017 in forum: Troubleshooting
  2. Jeff Meador
    Thread

    Solved New R1+ Not Autoleveling correctly

    New R1+, right out of box. When it goes to do the 9 pt autoleveling it starts in the middle (not X0 Y0 Z0) and then goes to the right. Next it...
    Thread by: Jeff Meador, May 5, 2017, 2 replies, in forum: Troubleshooting
  3. Jeff Meador
    Post

    Answered How to readjust the z offset

    In your slicer software, you should be able to go under settings and make the adjustment. Sent from my VS990 using Tapatalk
    Post by: Jeff Meador, May 2, 2017 in forum: Troubleshooting
  4. Jeff Meador
    Post

    Partial Answer Been having bad luck with filament. What brand should I buy?

    Honestly, I have been using Inland 1.75mm PLA from microcenter.com and it has been the most consistent one for me. Sent from my VS990 using Tapatalk
    Post by: Jeff Meador, Apr 20, 2017 in forum: Troubleshooting
  5. Jeff Meador
    Post

    Answered Mintemp Error

    The wires and plug are tight. Sent from my VS990 using Tapatalk
    Post by: Jeff Meador, Apr 3, 2017 in forum: Troubleshooting
  6. Jeff Meador
    Thread

    Answered Mintemp Error

    I tried using an oiler with canola oil, printing at 210. Filament wouldn't stick. Tried again, same thing (removed oiler). Probably put too...
    Thread by: Jeff Meador, Apr 2, 2017, 3 replies, in forum: Troubleshooting
  7. Jeff Meador
    Post

    Solved PLA not sticking

    Mark, thank you very much. Got it figured out in MC. Great thanks for your responsiveness and insight. Very, very helpful. Sent from my...
    Post by: Jeff Meador, Feb 5, 2017 in forum: Troubleshooting
  8. Jeff Meador
    Post

    Solved PLA not sticking

    Where do I find these? In arduino program? Where? Sent from my VS990 using Tapatalk
    Post by: Jeff Meador, Feb 4, 2017 in forum: Troubleshooting
  9. Jeff Meador
    Thread

    Solved PLA not sticking

    I recently switched out my hot end for an e3dv6 and uploaded the firmware. I am having a very hard time getting the pla to stick to my hot bed...
    Thread by: Jeff Meador, Feb 4, 2017, 4 replies, in forum: Troubleshooting
  10. Jeff Meador
    Post

    Answered Bad print after firmware change

    Thank you both. Just updated. Will try printing tomorrow as I added a bit of heat resistant red silicone to the top of the heatsink (similar to...
    Post by: Jeff Meador, Jan 30, 2017 in forum: Troubleshooting
  11. Jeff Meador
    Post

    Answered Bad print after firmware change

    The firmware used was this: For printers with Auto-level switches that does not have the previously described features, use this:...
    Post by: Jeff Meador, Jan 30, 2017 in forum: Troubleshooting
  12. Jeff Meador
    Thread

    Answered Bad print after firmware change

    I have a Robo 3D R1 Plus, and over the weekend upgraded to the E3D V6 hotend. When looking at which dropbox to install (e.g. rods that go up to...
    Thread by: Jeff Meador, Jan 30, 2017, 7 replies, in forum: Troubleshooting
  13. Jeff Meador
    Post

    E3D v6 Information, Installation Guides, and Review

    After updating arduino firmware, here is my print this am. The layers are stringy, almost like a thatch hut. Please take into account I am new...
    Post by: Jeff Meador, Jan 30, 2017 in forum: Mods and Upgrades
  14. Jeff Meador
    Post

    E3D v6 Information, Installation Guides, and Review

    Got it finally! Thanks guys for all the help and quick responses.
    Post by: Jeff Meador, Jan 29, 2017 in forum: Mods and Upgrades
  15. Jeff Meador
    Post

    E3D v6 Information, Installation Guides, and Review

    So without updating, I did a print last night and turned out good. So do I even need the update? Auto-leveling is working.... Sent from my...
    Post by: Jeff Meador, Jan 29, 2017 in forum: Mods and Upgrades
  16. Jeff Meador
    Post

    E3D v6 Information, Installation Guides, and Review

    Hi Mark, Ok, so I did a Ctrl-F and input the fpos_t, replace with filepos_t, clicked on Find and Replace (quite a few times), and now I get this:...
    Post by: Jeff Meador, Jan 28, 2017 in forum: Mods and Upgrades
  17. Jeff Meador
    Post

    E3D v6 Information, Installation Guides, and Review

    I installed arduino software, etc. The Z-axis rods go to the top (not the threaded) and I have the bottom plate, so I selected the first file that...
    Post by: Jeff Meador, Jan 28, 2017 in forum: Mods and Upgrades
  18. Jeff Meador
    Thread

    Unanswered Cut planes and measure

    Netfabb has a great plane cutter, but goes away after free trial. Meshmixer has the ability to cut planes and measure, but the measurement is so...
    Thread by: Jeff Meador, Jan 7, 2017, 2 replies, in forum: Troubleshooting
  19. Jeff Meador
    Thread

    Unanswered Mother of all fan brackets

    I saw the thingiverse link for the Mother of all fan brackets. I'd love to print the correct one for the standard fan that comes on the bottom...
    Thread by: Jeff Meador, Jan 6, 2017, 0 replies, in forum: Troubleshooting
  20. Jeff Meador
    Post

    Unanswered Printing larger scale objects

    Thanks Geof, and I appreciate the welcome as well!
    Post by: Jeff Meador, Dec 18, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2