1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 6
  1. spankurmonkey
    Post

    Unresolved Failed Overhang

    Here are the results afterwards..... seems pretty much the same as the first ones... [img] [img]
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  2. spankurmonkey
    Post

    Unresolved Failed Overhang

    That explains it.. but I will say when I tried a M500 in Octoprint it just timed out.
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  3. spankurmonkey
    Post

    Unresolved Failed Overhang

    Still baffled why the firmware update and then the M503 through Octoprint didn't work but now I realize I can change this via the XXL Smart...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  4. spankurmonkey
    Post

    Unresolved Failed Overhang

    I am at a dead stop now.... for the last hour I have been trying to update the firmware. I load Arduino making sure the robo is connected to my...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  5. spankurmonkey
    Post

    Unresolved Failed Overhang

    First, I ran both print tests - untouched with standard settings in S3D. To me , both prints passed the test. [IMG] [IMG] I then ran the...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  6. spankurmonkey
    Post

    Unresolved Failed Overhang

    // Define this to set a custom name for your generic Mendel, #define CUSTOM_MENDEL_NAME "ROBOR1PLUSV1" //robo #define...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  7. spankurmonkey
    Post

    Unresolved Failed Overhang

    In regards to changes to the firmware.. I had the smaller LCD which required a firmware change... then I got the XXL so I switch it back. No...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  8. spankurmonkey
    Post

    Unresolved Failed Overhang

    I will run the extrusion tests today. When I printed the MPCNC part where the overhang failed I was printing at .26 layer height. Just so I am...
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  9. spankurmonkey
    Post

    Unresolved Failed Overhang

    someone on here told me to start at .10 - When I first got the printer only messing with the firmware was to accept the lcd controller that's it....
    Post by: spankurmonkey, Feb 26, 2017 in forum: Troubleshooting
  10. spankurmonkey
    Post

    Unresolved Failed Overhang

    Is it possible that in S3D I messed something up... I.e. Nozzle Diameter, Extrusion Multiplier, Extrusion width, etc?? I am baffled .. I...
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  11. spankurmonkey
    Post

    Unresolved Failed Overhang

    Such as ??? I am having a hard time troubleshooting this..
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  12. spankurmonkey
    Post

    Unresolved Failed Overhang

    I ran this at 190 with these two fans at 100% Some areas the print looks like it should and other, especially on the right side, have this...
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  13. spankurmonkey
    Post

    Unresolved Failed Overhang

    failed again.. right side at the 190c... not as bad but no sense in continuing the print.
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  14. spankurmonkey
    Post

    Unresolved Failed Overhang

    Temp tower test.. not sure what that is...
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  15. spankurmonkey
    Post

    Unresolved Failed Overhang

    So I have swapped back to two stock fans on the Black Widow mount - no ducts and lowered temp to 190c. I am using inland PLA black so at 190c...
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  16. spankurmonkey
    Post

    Unresolved Failed Overhang

    well I have tinkered the last week with various fan designs, etc and still no good solution. I tried printing a very simple planter object that...
    Post by: spankurmonkey, Feb 25, 2017 in forum: Troubleshooting
  17. spankurmonkey
    Post

    Unresolved Failed Overhang

    Picture would be great.
    Post by: spankurmonkey, Feb 22, 2017 in forum: Troubleshooting
  18. spankurmonkey
    Post

    Unresolved Failed Overhang

    Well --- total fail now..... keep getting temp error and the print stop now.
    Post by: spankurmonkey, Feb 21, 2017 in forum: Troubleshooting
  19. spankurmonkey
    Post

    Unresolved Failed Overhang

    I am now printing another set of ducts for this black widow set up.... the duct that comes with that thingy is fine for the forward fan but the...
    Post by: spankurmonkey, Feb 21, 2017 in forum: Troubleshooting
  20. spankurmonkey
    Post

    Unresolved Failed Overhang

    So I mounted the Black Widow mount from Thingiverse today. http://www.thingiverse.com/thing:821080 I have the stock fans mounted to it now...
    Post by: spankurmonkey, Feb 21, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 102 Next >
Search Again
Page 1 of 6