1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Charles Billette
    Post

    Bed Calibration

    Removing the G29 and manually levelling did the trick! Is is now near to perfect
    Post by: Charles Billette, Jun 23, 2017 in forum: Troubleshooting
  2. Charles Billette
    Post

    Bed Calibration

    Found the script. Just needed to scroll, Doh! :)
    Post by: Charles Billette, Jun 23, 2017 in forum: Troubleshooting
  3. Charles Billette
    Post

    Bed Calibration

    Where am I suppose to find the G29 command ... The script I got for "Before print job starts" is ... ; set to millimeters G21 ; set to absolute...
    Post by: Charles Billette, Jun 23, 2017 in forum: Troubleshooting
  4. Charles Billette
    Thread

    Bed Calibration

    I'm struggling to get my bed calibration right. I did it does wizards many times ... Z offset Bed Calibration Fine tune Has you can see on the...
    Thread by: Charles Billette, Jun 23, 2017, 7 replies, in forum: Troubleshooting
  5. Charles Billette
    Thread

    Maker Faire Robot Action Figure

    This my first print with Simplify3D and the Robo R2 and it is almost perfect. 1.2 layer height 5000 mm/minutes or 85 mm/s print speed and I...
    Thread by: Charles Billette, Jun 6, 2017, 3 replies, in forum: Show and Tell
  6. Charles Billette
    Post

    Nosiey Power Brick

    Input : 100-240 VAC, 50/60Hz, 4.0Amp Output : 24v 9.2Amp 221w. MAX
    Post by: Charles Billette, Jun 6, 2017 in forum: Troubleshooting
  7. Charles Billette
    Post

    Nosiey Power Brick

    Can you confirm the number of watts the power supply need to output ... I do a have fan less 24v power supply at 227 watts is this going to be enough?
    Post by: Charles Billette, Jun 6, 2017 in forum: Troubleshooting
  8. Charles Billette
    Post

    Lightning Print Area

    All good. I unplugged and plug back the gray and blue wires and the led are now turn on.
    Post by: Charles Billette, Jun 4, 2017 in forum: General Questions
  9. Charles Billette
    Post

    Benchy on Robo R2 sliced with Simplify3D

    Can you export you simply3D profile and share it? Sent from my iPhone using Tapatalk
    Post by: Charles Billette, Jun 4, 2017 in forum: Show and Tell
  10. Charles Billette
    Thread

    Simplify 3D profile for Robo R2

    Any know if there is an existing Simplify 3D profile for Robo R2?
    Thread by: Charles Billette, Jun 2, 2017, 76 replies, in forum: Software
  11. Charles Billette
    Thread

    Lightning Print Area

    I was under the impression that the R2 add led inside to illuminate the print area? I think the are on both side of the door, Did I dream this?...
    Thread by: Charles Billette, Jun 2, 2017, 20 replies, in forum: General Questions
  12. Charles Billette
    Post

    Cura 2.5 for Apple MacOS broken.

    I'm expecting mine tomorrow. So I want to be ready :)
    Post by: Charles Billette, May 30, 2017 in forum: Software
  13. Charles Billette
    Post

    Cura 2.5 for Apple MacOS broken.

    I was under the impression that the Robo version have specific features for the R2 printer?
    Post by: Charles Billette, May 30, 2017 in forum: Software
  14. Charles Billette
    Thread

    Cura 2.5 for Apple MacOS broken.

    When I try to download Cura from the software page the MacOS link is broken. Where can I download the software for Mac? Thanks
    Thread by: Charles Billette, May 30, 2017, 7 replies, in forum: Software
Showing results 1 to 14 of 14
Search Again