1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Guys, I think my Robo has a soul and a brain ( an autonomous one) and a character as well. Now, after I achieved a good level of printing........
    Post by: Sorin Mihai, May 13, 2018 in forum: Troubleshooting
  2. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    As a slicer I used CuraEngine!
    Post by: Sorin Mihai, May 11, 2018 in forum: Troubleshooting
  3. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    And the result after changes: [ATTACH] I think is a visible change (so far)!
    Post by: Sorin Mihai, May 11, 2018 in forum: Troubleshooting
  4. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thanks guys, I am using Slic3r for the moment with MC. I have the option to go for CuraEngine or MatterSlice. Are any of these good and how can I...
    Post by: Sorin Mihai, May 11, 2018 in forum: Troubleshooting
  5. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Hi Mark, sorry for the silence, I've been preparing for some exams. Today I had some time to work more on the Robo and I modified the Marlin 1.1.8...
    Post by: Sorin Mihai, May 10, 2018 in forum: Troubleshooting
  6. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    I am using 1.1.4 for the moment. But I,'ll try with seting the Z offset before G29. Thank you !
    Post by: Sorin Mihai, May 1, 2018 in forum: Troubleshooting
  7. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Hi Mark, Just finish the upgrade for bed auto-levelling, works ok, looks ok. In firmware I am keeping the #define...
    Post by: Sorin Mihai, May 1, 2018 in forum: Troubleshooting
  8. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Hi Mark, for autobed levelling, do I still need the old Z switch or I should cancel it and keep only the 2 new ones?
    Post by: Sorin Mihai, Apr 30, 2018 in forum: Troubleshooting
  9. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thanks Mark, I did had my extruder extruding 110mm instead of 100. Fix it. Great video, really appreciated!
    Post by: Sorin Mihai, Apr 29, 2018 in forum: Troubleshooting
  10. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thanks Mark, can you put that link for the video with "warping"? I can't see it! I did a small test, I've changed the 2 thermistors on the Ramps,...
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  11. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thank you! I took it out to check it and is working, meaning that with the thermistor connected on my multimeter, if I take it in the fridge the...
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  12. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    That was my initial thought, but know is too late to go back cus I don't even have the first firmware. Anyway, only by persisting I can solve...
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  13. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    OK, the temp error happened again before printing, 10 sec after I start the printing. All temp were ok. I will try the last release of Marlin.
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  14. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Hi, this is the error, and is weird cus the bed temp is actually at 60 as it should be and I still got the error. Please help![ATTACH]
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  15. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thanks Mark, very helpful topic. I have ordered the micro switches, I have the rest apart the couplings.... and I can't find them in all...
    Post by: Sorin Mihai, Apr 28, 2018 in forum: Troubleshooting
  16. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Hi Mark, can you see the third image, I think the wiring one? I cant. can you send it to me or post it here? thank you!
    Post by: Sorin Mihai, Apr 27, 2018 in forum: Troubleshooting
  17. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Did as you said, printed the switches mounts, without M851 and G29 in the start G-code, just manual spinning of the rods. Personally I think that...
    Post by: Sorin Mihai, Apr 27, 2018 in forum: Troubleshooting
  18. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    I will try the Marlin 1.1.4 to see if I get improvements on positioning of the hotend. I'll be back!
    Post by: Sorin Mihai, Apr 27, 2018 in forum: Troubleshooting
  19. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thanks Mark for your precious informations and tips. I will start upgrading the printer. Can you recommend a model number for the switches or/and...
    Post by: Sorin Mihai, Apr 27, 2018 in forum: Troubleshooting
  20. Sorin Mihai
    Post

    Answered Robo3D R1 multiple issues

    Thank Mark for the light and the fog :)). You mean to mount 2 switches on the crossbar? And if I have a beta... can I upgrade it to a R1 or R1+?...
    Post by: Sorin Mihai, Apr 27, 2018 in forum: Troubleshooting
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2