1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    I don't believe I was printing too hot, because I was printing at 200 in PLA.
    Post by: Matthew Schwartz, Feb 28, 2017 in forum: Troubleshooting
  2. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    Thank you guys for helping, It was the print speed that was the issue.
    Post by: Matthew Schwartz, Feb 27, 2017 in forum: Troubleshooting
  3. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    That's exactly what I did but it didn't work. This is a good example on how its coming out though...
    Post by: Matthew Schwartz, Feb 27, 2017 in forum: Troubleshooting
  4. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    This is a good example of how it looks. This is a image I found on Bing and resembles quite well....
    Post by: Matthew Schwartz, Feb 27, 2017 in forum: Troubleshooting
  5. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    I tried doing that but when I do it gives me this " Security error occurred. Please press back, refresh the page, and try again."
    Post by: Matthew Schwartz, Feb 27, 2017 in forum: Troubleshooting
  6. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    How do I insert a image then?
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  7. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    It shows me a picture. | | Ill insert one...
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  8. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    There is a picture below the description of the problem.
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  9. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    Do you know how to make it so it doesn't come out so bad. A couple days ago that model was printing perfectly fine, but now it is printing that...
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  10. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    Thank you for helping me with what you could do. I was just comparing the prints that had come out, and I noticed a drastic change in quality.
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  11. Matthew Schwartz
    Post

    Solved My prints are coming out at terrible quality

    I am using the regular slicer MatterControl. It's only a few models it having that issue with, I'm using 210 and 50 for the nozzle and bed....
    Post by: Matthew Schwartz, Feb 26, 2017 in forum: Troubleshooting
  12. Matthew Schwartz
    Thread

    Solved My prints are coming out at terrible quality

    I have the ROBO 3D R1 Plus printer. My biggest issue with this printer is the quality of the prints have been terrible. This has been going on for...
    Thread by: Matthew Schwartz, Feb 26, 2017, 28 replies, in forum: Troubleshooting
  13. Matthew Schwartz
    Thread

    Solved My prints are coming out at terrible quality

    I am printing at 1 infill and 0.2mm layer height and the prints just aren't coming out good. [IMG] [IMG]
    Thread by: Matthew Schwartz, Feb 26, 2017, 1 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again