1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jay312
    Thread

    Any recommendations for 2D image to 3D model software

    looking for software (easy to use) to make a normal 2d photo into a 3D model .stl file that I can print. Any recommendations?
    Thread by: Jay312, Mar 9, 2018, 2 replies, in forum: Software
  2. Jay312
    Thread

    Partial Answer Possible short?

    So I finished my E3D V6 and XXL LCD controller, on my R1 Plus. Printer has been printing great for about a week. Now two issues are happening A)...
    Thread by: Jay312, Aug 9, 2017, 18 replies, in forum: Troubleshooting
  3. Jay312
    Thread

    Solved Problem

    After installing the E3D V6 it's printing in the air and leveling in the air. I did check the wires because that's almost always the issue, but...
    Thread by: Jay312, Jul 28, 2017, 3 replies, in forum: Troubleshooting
  4. Jay312
    Thread

    E3D V6 Help

    Before I drill a hole for the tube do I need to take this apart completely, I'm worried about hitting that metal thing that feeds the filament...
    Thread by: Jay312, Jul 17, 2017, 14 replies, in forum: Mods and Upgrades
  5. Jay312
    Thread

    Filament spool print

    Printed on my R1 Plus with Robo Carbon Fiber PLA I actually used two different ithingverse builds to make this one build. Snaps in sturdy.
    Thread by: Jay312, Apr 3, 2017, 5 replies, in forum: Show and Tell
  6. Jay312
    Thread

    Solved Sites like thingiverse?

    Looking for some other sites like thingiverse I know I have to be missing out on some cool ones. What does everyone like?
    Thread by: Jay312, Apr 3, 2017, 8 replies, in forum: General Questions
  7. Jay312
    Thread

    Solved Auto leveling problem

    Had some issues where my Z axsis was stuck up top and a cable on the end motor came out, fixed all that. But now when I start a print when it goes...
    Thread by: Jay312, Apr 1, 2017, 13 replies, in forum: Troubleshooting
  8. Jay312
    Thread

    My workstation setup

    Not the greatest but not bad, I'm happy with it. [ATTACH]
    Thread by: Jay312, Mar 29, 2017, 7 replies, in forum: Show and Tell
  9. Jay312
    Thread

    Solved How do you properly remove Filament

    So my big problem this week was I tried a new Filament and I wanted to switch colors so I just cut the old filament and thought I extruded it, I...
    Thread by: Jay312, Mar 27, 2017, 4 replies, in forum: General Questions
  10. Jay312
    Thread

    Solved 357 degree extruder temp

    Finally found my grub screw now I'm dealing with a 357 degree extruder temp and it's not even a little heated? Any ideas
    Thread by: Jay312, Mar 25, 2017, 4 replies, in forum: Troubleshooting
  11. Jay312
    Thread

    Solved Any help or ideas

    carbon PTEG won't budge, tried plugging back into the printer but hanging and the temp on matter control was very off so it would not heat
    Thread by: Jay312, Mar 25, 2017, 9 replies, in forum: Troubleshooting
  12. Jay312
    Thread

    One More Newbie Question (Print Quality)

    This question is about Print Quality: 1. besides changing the settings to fine, would slowing down how fast the printer printed help with better...
    Thread by: Jay312, Mar 20, 2017, 2 replies, in forum: General Questions
  13. Jay312
    Thread

    Solved A few questions from a newbie

    I just got and setup my robo 3d R1+ last night. I must say so far im extremely happy with the purchase. Printed the calibration Circle and even...
    Thread by: Jay312, Mar 18, 2017, 14 replies, in forum: General Questions
Showing results 1 to 13 of 13
Search Again