1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Martyprints
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    my robo r1+ board has 2 pin end stops, is there any way i can still use this? i bought one from filastruder. there's no third pin or even a hole...
    Post by: Martyprints, May 17, 2018 in forum: Mods and Upgrades
  2. Martyprints
    Post

    Partial Answer X Axis becoming uneven (not level) after pause

    i sprayed a ton of silicon spray inside the motor, squeaking stopped, first test print turned out well. i hope that was the issue. gonna do a...
    Post by: Martyprints, Nov 17, 2017 in forum: Troubleshooting
  3. Martyprints
    Post

    Partial Answer X Axis becoming uneven (not level) after pause

    i can't figure out where the squeak is coming from and this issue is still happening. could it be a bad motor?
    Post by: Martyprints, Nov 17, 2017 in forum: Troubleshooting
  4. Martyprints
    Post

    Partial Answer X Axis becoming uneven (not level) after pause

    I'll try that, i do hear a squeak when the z is moving so that could be it.
    Post by: Martyprints, Nov 12, 2017 in forum: Troubleshooting
  5. Martyprints
    Post

    Partial Answer X Axis becoming uneven (not level) after pause

    i don't have an LCD and i use mattercontrol. i like MC, it works well for me.
    Post by: Martyprints, Nov 12, 2017 in forum: Troubleshooting
  6. Martyprints
    Thread

    Partial Answer X Axis becoming uneven (not level) after pause

    So i have a set up my pause G Code to move the nozzle up and away so i could change filament. It works sometimes but other times the x axis...
    Thread by: Martyprints, Nov 10, 2017, 9 replies, in forum: Troubleshooting
  7. Martyprints
    Post

    E3D Titan Aero combo announced

    so at 750mm/s it extrudes 100mm in controls on mattercontrol but it under extrudes horribly when printing. the layers literally have gaps between...
    Post by: Martyprints, Jul 29, 2017 in forum: Off Topic
  8. Martyprints
    Post

    E3D Titan Aero combo announced

    it extrudes correclty at 750 steps/mm. so basically stock settings. i honestly don't get it, but whatever.
    Post by: Martyprints, Jul 29, 2017 in forum: Off Topic
  9. Martyprints
    Post

    E3D Titan Aero combo announced

    ok so i've done all that and at 458 steps/mm it's extruding half... i don't get it. it's extruding like 50mm
    Post by: Martyprints, Jul 29, 2017 in forum: Off Topic
  10. Martyprints
    Post

    E3D Titan Aero combo announced

    ok, how do i input the M500 and M501 gcodes? using the arduino app?
    Post by: Martyprints, Jul 29, 2017 in forum: Off Topic
  11. Martyprints
    Post

    E3D Titan Aero combo announced

    hey guys, so i've installed an aero on my robo and i'm having underextrusion issues no matter what i do. i have the steps at 700 and it's not...
    Post by: Martyprints, Jul 28, 2017 in forum: Off Topic
Showing results 1 to 11 of 11
Search Again