1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Echoshard
    Post

    R2 Click and Snapping Sounds

    Increase your temp to ~220 C and see if you get the same issue. I think the sensor is lying to me.
    Post by: Echoshard, Aug 21, 2017 in forum: Troubleshooting
  2. Echoshard
    Post

    Power Supply Fan Whine

    So some good news if any of you saw the 3D Printing Nerds video they have a new power supply! [MEDIA] At 8 mins 38 Seconds
    Post by: Echoshard, Aug 21, 2017 in forum: Troubleshooting
  3. Echoshard
    Post

    Power Supply Fan Whine

    I already did they don't have any in stock they can send me.
    Post by: Echoshard, Jul 27, 2017 in forum: Troubleshooting
  4. Echoshard
    Post

    Power Supply Fan Whine

    I have printing for over a week without the fan. It seems as long as I don't draw too much power it seems to be running fine. I am printing PLA...
    Post by: Echoshard, Jul 27, 2017 in forum: Troubleshooting
  5. Echoshard
    Post

    R2 Click and Snapping Sounds

    Ok so Support told me to replace the barrings and the clicking is still here. Sadly I will keep investigating
    Post by: Echoshard, Jul 27, 2017 in forum: Troubleshooting
  6. Echoshard
    Post

    Power Supply Fan Whine

    It's been printing for 24 hours with no issues.
    Post by: Echoshard, Jul 18, 2017 in forum: Troubleshooting
  7. Echoshard
    Post

    Power Supply Fan Whine

    18 Watts is insane! I opened mine up and put some drops of oil on it however just a few days later the whine was back. I just disconnected the...
    Post by: Echoshard, Jul 18, 2017 in forum: Troubleshooting
  8. Echoshard
    Post

    R2 Click and Snapping Sounds

    So I spent a good day disassembling the entire extruder assembly. Oiled it put it back together. After sacrificing a few goats it's up and...
    Post by: Echoshard, Jul 5, 2017 in forum: Troubleshooting
  9. Echoshard
    Post

    Power Supply Fan Whine

    After a large amount of percussive maintenance the fan did not actually stop whining it stayed the same or got worse. I will be discussing it with...
    Post by: Echoshard, Jul 5, 2017 in forum: Troubleshooting
  10. Echoshard
    Thread

    Power Supply Fan Whine

    So, Today I came in to see that the power supply fan is making horrible noises. Is it required to run? Anyone know I am thinking of just...
    Thread by: Echoshard, Jul 4, 2017, 50 replies, in forum: Troubleshooting
  11. Echoshard
    Post

    R2 Click and Snapping Sounds

    Yea I don't think this actually anything on the extruder, Even with the filament entirely clear it still makes those noises Great you were able to...
    Post by: Echoshard, Jul 2, 2017 in forum: Troubleshooting
  12. Echoshard
    Post

    R2 Click and Snapping Sounds

    I kinda don't want to risk that I could damage the printer more. I will send an email to support.
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  13. Echoshard
    Post

    R2 Click and Snapping Sounds

    Thanks Ed, I tried all that and it did nothing vibration wise it seems like it's like the snap inside case..
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  14. Echoshard
    Post

    R2 Click and Snapping Sounds

    So I was finally able to get it to reproduce the click. It requires me to go all the way from Zero to max on the X Axis. It clicks on any Y axis....
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  15. Echoshard
    Post

    R2 Click and Snapping Sounds

    I take it theirs no good manual for disassembly is there?
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  16. Echoshard
    Post

    R2 Click and Snapping Sounds

    See that's the really odd thing it only seems to happen while printing. I used the motor controls to try and do it myself it's whisper quite. I...
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  17. Echoshard
    Post

    R2 Click and Snapping Sounds

    Fixed it Sorry about that it's on the X/Y Axis not the Z
    Post by: Echoshard, Jun 30, 2017 in forum: Troubleshooting
  18. Echoshard
    Thread

    R2 Click and Snapping Sounds

    Hello, I am having some odd clicks and snapping sounds coming from the printer. Here are some videos [MEDIA] [MEDIA] Do I need to tighten...
    Thread by: Echoshard, Jun 30, 2017, 85 replies, in forum: Troubleshooting
  19. Echoshard
    Post

    Issues out of the box...

    I also had a really badly scratched up door.
    Post by: Echoshard, Jun 5, 2017 in forum: Troubleshooting
  20. Echoshard
    Post

    Print Bed Adhesion

    Ok after much effort I was able to get parts to adhere correctly. Lowering the bed temp to 55 did wonders. Apparently the somehow the build plate...
    Post by: Echoshard, Jun 5, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 29 Next >
Search Again
Page 1 of 2