1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Shawn Wandler
    Post

    Solved original R1 firmware

    Thankyou
    Post by: Shawn Wandler, Dec 14, 2017 in forum: Troubleshooting
  2. Shawn Wandler
    Thread

    Solved original R1 firmware

    Hi I am trying to find the original firmware for the R1 so that I can restore my R1 to factory settings can anyone direct me to where I may find it.
    Thread by: Shawn Wandler, Dec 14, 2017, 2 replies, in forum: Troubleshooting
  3. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    I have now changed the Arduino board the ramps board and all the drivers and both stepper Motors and I still get the same grinding really don't...
    Post by: Shawn Wandler, Sep 3, 2017 in forum: Troubleshooting
  4. Shawn Wandler
    Post

    Answered Z motors not moving when attached

    I was thinking about doing the the swap with the connectors as well I do have a sneaking suspicion that it's going to be a wire but can't say for...
    Post by: Shawn Wandler, Jul 21, 2017 in forum: Troubleshooting
  5. Shawn Wandler
    Post

    Answered Z motors not moving when attached

    Sorry i meant stepper motor. I had just picked up a full set like your 2nd link.
    Post by: Shawn Wandler, Jul 21, 2017 in forum: Troubleshooting
  6. Shawn Wandler
    Post

    Answered Z motors not moving when attached

    Can you recommend a good replacement stepper driver possibly from Amazon good to have spares even if that's not the problem
    Post by: Shawn Wandler, Jul 21, 2017 in forum: Troubleshooting
  7. Shawn Wandler
    Post

    Answered Z motors not moving when attached

    Yes I did the stepper motor tuning I am now at 6.2 on the Z driver
    Post by: Shawn Wandler, Jul 21, 2017 in forum: Troubleshooting
  8. Shawn Wandler
    Post

    Answered Z motors not moving when attached

    Did you ever solve this issue? I have the same Issue
    Post by: Shawn Wandler, Jul 21, 2017 in forum: Troubleshooting
  9. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    Well I have now checked the voltage on the drivers and they are set fine I have replaced both and end stops on the Z axis and still have the same...
    Post by: Shawn Wandler, Jul 20, 2017 in forum: Troubleshooting
  10. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    I'll give that a go when I get home from work. I did read some-ware that someone had a similar issue after they upgraded there firmware could this...
    Post by: Shawn Wandler, Jul 18, 2017 in forum: Troubleshooting
  11. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    [MEDIA]
    Post by: Shawn Wandler, Jul 17, 2017 in forum: Troubleshooting
  12. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    Well here's where I stand now. I have changed the Arduino board the ramps board all the drivers. The firmware is now installed and running...
    Post by: Shawn Wandler, Jul 17, 2017 in forum: Troubleshooting
  13. Shawn Wandler
    Post

    Solved How to Ramps Board for R1

    yes that's it exactly thank-you
    Post by: Shawn Wandler, Jul 17, 2017 in forum: Troubleshooting
  14. Shawn Wandler
    Post

    Solved How to Ramps Board for R1

    Sorry it's for the R1
    Post by: Shawn Wandler, Jul 17, 2017 in forum: Troubleshooting
  15. Shawn Wandler
    Thread

    Solved How to Ramps Board for R1

    Hi I am looking for a diagram that clearly shows the wiring for the ramps board on the R1 also witch way the plug goes onto the board. Thanks
    Thread by: Shawn Wandler, Jul 17, 2017, 6 replies, in forum: Troubleshooting
  16. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    Here is an other video of my problem. The X-axis will move up but only when aided with my hand assisting wondering if it could be a bad driver?...
    Post by: Shawn Wandler, Jul 11, 2017 in forum: Troubleshooting
  17. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    I did order this if the issue is with the arduino or ramps. https://www.amazon.ca/gp/product/B0188ULASE/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
    Post by: Shawn Wandler, Jul 11, 2017 in forum: Troubleshooting
  18. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    After fooling around trying to put the graphics display on and dealing with a clogged extruder one of the left side wires on the limit switch...
    Post by: Shawn Wandler, Jul 11, 2017 in forum: Troubleshooting
  19. Shawn Wandler
    Post

    Partial Answer X Axis not moving

    This is where I got the firmware from. http://guide.robo3d.com/Wiki/ROBO_3D_Firmware_Release_Notes#Section_ROBO_R1_Original_Firmware_3_Num_0 I...
    Post by: Shawn Wandler, Jul 11, 2017 in forum: Troubleshooting
  20. Shawn Wandler
    Thread

    Partial Answer X Axis not moving

    After trying to install a rep-rap full graphic display and updating the firmware to no avail I went back to stock firmware and removed the graphic...
    Thread by: Shawn Wandler, Jul 11, 2017, 18 replies, in forum: Troubleshooting
Showing results 1 to 20 of 57 Next >
Search Again
Page 1 of 3