1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Mr Wire
    Post

    new stock hotend

    understood but please clarify "TYPE of the thermistor for Marlin is the same"
    Post by: Mr Wire, Apr 17, 2019 in forum: Mods and Upgrades
  2. Mr Wire
    Post

    new stock hotend

    is this the correct one? or can you provide a amazon link? There is a standard and a AO item 1x 1.75mm all metal Hexagon hotend 1x Nozzle 0.4mm...
    Post by: Mr Wire, Apr 16, 2019 in forum: Mods and Upgrades
  3. Mr Wire
    Thread

    new block and 0.4 nozzle bronce for PLA

    hello ive changed the original aluminum block ( a little bigger ) and a 0.4 nozzle ( ive read is the stock size) do i need to change any settiing...
    Thread by: Mr Wire, Apr 16, 2019, 0 replies, in forum: Mods and Upgrades
  4. Mr Wire
    Thread

    new stock hotend

    hello, where can I buy a new stock hotend to replace factory one? I do not want to upgrade thanks
    Thread by: Mr Wire, Apr 16, 2019, 5 replies, in forum: Mods and Upgrades
  5. Mr Wire
    Post

    Solved extruder cable came off

    yes, i was not sure then were to stick it now i know it goes in the small tube next to the other cable i need high temp silicone to do it thanks!
    Post by: Mr Wire, Nov 6, 2018 in forum: Troubleshooting
  6. Mr Wire
    Thread

    Solved extruder cable came off

    hello cleaning the extruder, the black and red cable came off of the extruder. how do i stick it back? the correct side? extr or extr2 thanks
    Thread by: Mr Wire, Nov 6, 2018, 3 replies, in forum: Troubleshooting
  7. Mr Wire
    Post

    Solved calibration rods

    solved! thanks!
    Post by: Mr Wire, Nov 26, 2017 in forum: Troubleshooting
  8. Mr Wire
    Post

    Solved calibration rods

    ok using the paper gauge technic , need to only adjust left rod. it feels all the bed is with the same height all around no need to touch the...
    Post by: Mr Wire, Nov 24, 2017 in forum: Troubleshooting
  9. Mr Wire
    Post

    Solved calibration rods

    tell me how to park the extruder at the correct height for leveling?
    Post by: Mr Wire, Nov 24, 2017 in forum: Troubleshooting
  10. Mr Wire
    Post

    Solved calibration rods

    understood when available , tell me how to park the extruder at the correct height for leveling enjoy the Turkey !
    Post by: Mr Wire, Nov 23, 2017 in forum: Troubleshooting
  11. Mr Wire
    Post

    Solved calibration rods

    can you provide a pic of what i need to level? I can see the magnets, but i dont want to to the wrong thing
    Post by: Mr Wire, Nov 23, 2017 in forum: Troubleshooting
  12. Mr Wire
    Post

    Solved calibration rods

    that is the side from the bed it looks that those corners does not stick properly ( im using spray and double checked the surface is covered...
    Post by: Mr Wire, Nov 23, 2017 in forum: Troubleshooting
  13. Mr Wire
    Thread

    Solved calibration rods

    hello all looking the robo printer from the the front printing a rectangle the first layer from the center to the right , all corners 100 %...
    Thread by: Mr Wire, Nov 23, 2017, 11 replies, in forum: Troubleshooting
  14. Mr Wire
    Thread

    Unanswered xxl smart lcd enclosure

    hello all looking into different enclosures, can you recommend one?, there are many options and not sure the best one tested and updated to print...
    Thread by: Mr Wire, Nov 22, 2017, 1 replies, in forum: General Questions
  15. Mr Wire
    Post

    Solved custom G code

    Ive made it! perfect and incredible first layer used Z-1.0 thank you all
    Post by: Mr Wire, Nov 15, 2017 in forum: Troubleshooting
  16. Mr Wire
    Post

    Solved custom G code

    between the bed and the extruder , it has to have a paper sheet thickness gap?
    Post by: Mr Wire, Nov 15, 2017 in forum: Troubleshooting
  17. Mr Wire
    Post

    Solved custom G code

    Ok , ive typed in terminal M502; and then M500 see settings
    Post by: Mr Wire, Nov 15, 2017 in forum: Troubleshooting
  18. Mr Wire
    Post

    Solved custom G code

    i have no clue at all the only setting ive modified/ added is the one provided for the g code. i have no knowledge of changing other parameters...
    Post by: Mr Wire, Nov 14, 2017 in forum: Troubleshooting
  19. Mr Wire
    Post

    Solved custom G code

    its ok that i cannot slice a piece of paper under the extruder still with -0.9 ?
    Post by: Mr Wire, Nov 14, 2017 in forum: Troubleshooting
  20. Mr Wire
    Thread

    Solved custom G code

    Hi all suggested by this forum im using a custom g code G28 ; home all axes G1 Z5 F5000 ; lift Z by 5mm M565 Z-0.6 ; set the offset for...
    Thread by: Mr Wire, Nov 14, 2017, 13 replies, in forum: Troubleshooting
Showing results 1 to 20 of 47 Next >
Search Again
Page 1 of 3