1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Mr Wire
    Thread

    new block and 0.4 nozzle bronce for PLA

    hello ive changed the original aluminum block ( a little bigger ) and a 0.4 nozzle ( ive read is the stock size) do i need to change any settiing...
    Thread by: Mr Wire, Apr 16, 2019, 0 replies, in forum: Mods and Upgrades
  2. Mr Wire
    Thread

    new stock hotend

    hello, where can I buy a new stock hotend to replace factory one? I do not want to upgrade thanks
    Thread by: Mr Wire, Apr 16, 2019, 5 replies, in forum: Mods and Upgrades
  3. Mr Wire
    Thread

    Solved extruder cable came off

    hello cleaning the extruder, the black and red cable came off of the extruder. how do i stick it back? the correct side? extr or extr2 thanks
    Thread by: Mr Wire, Nov 6, 2018, 3 replies, in forum: Troubleshooting
  4. Mr Wire
    Thread

    Solved calibration rods

    hello all looking the robo printer from the the front printing a rectangle the first layer from the center to the right , all corners 100 %...
    Thread by: Mr Wire, Nov 23, 2017, 11 replies, in forum: Troubleshooting
  5. Mr Wire
    Thread

    Unanswered xxl smart lcd enclosure

    hello all looking into different enclosures, can you recommend one?, there are many options and not sure the best one tested and updated to print...
    Thread by: Mr Wire, Nov 22, 2017, 1 replies, in forum: General Questions
  6. Mr Wire
    Thread

    Solved custom G code

    Hi all suggested by this forum im using a custom g code G28 ; home all axes G1 Z5 F5000 ; lift Z by 5mm M565 Z-0.6 ; set the offset for...
    Thread by: Mr Wire, Nov 14, 2017, 13 replies, in forum: Troubleshooting
  7. Mr Wire
    Thread

    Solved first layer print issue

    once again struggleling with the first layer please see pics # and #2 same settings 210 extruder 50 bed PLA pic # 3 200 extruder 50 bed please...
    Thread by: Mr Wire, Nov 8, 2017, 0 replies, in forum: Troubleshooting
  8. Mr Wire
    Thread

    Partial Answer mac power settings script to print

    hello Is there any script I can use to change energy settings / mac so the printer does not sleep and when printing and then mattercontrol...
    Thread by: Mr Wire, Nov 6, 2017, 7 replies, in forum: Troubleshooting
  9. Mr Wire
    Thread

    Solved printing issue / problem / filament issue

    hello ive designed this water valve handle it fits ok, no problem it looks it gets rounded because the plastic is too soft any suggestions? thank...
    Thread by: Mr Wire, Oct 16, 2017, 13 replies, in forum: Troubleshooting
  10. Mr Wire
    Thread

    Unanswered PLA and FAN

    Hello How do I know the use or not of the fan for PLA? thanks
    Thread by: Mr Wire, Jul 13, 2017, 11 replies, in forum: General Questions
  11. Mr Wire
    Thread

    Partially Solved first layer problem

    hello never had this issue before and suddenly prints the first layer like a fried egg, see pic please help. thanks in advance MAC MATTERCONTROL...
    Thread by: Mr Wire, Jul 9, 2017, 8 replies, in forum: Troubleshooting
  12. Mr Wire
    Thread

    Solved print wont stick into bed

    hello on my new print, it wont stick into pre heated bed ( 50c) ive used provided glue and spray it starts printing ok, but it seems that the heat...
    Thread by: Mr Wire, Jun 11, 2017, 15 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again