1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. AntiReality
    Post

    Answered Z Axis Triggered Issue

    The crimp connectors fit snugly on the terminals, wire doesn't appear to be corroded in the crimped sections. Perhaps later ill flip the machine...
    Post by: AntiReality, Jan 9, 2019 in forum: Troubleshooting
  2. AntiReality
    Post

    Answered Z Axis Triggered Issue

    Driving me nutty, as I had near perfect first layers with Marlin 1.1.7 late last year then it panicked. Reverted back to R1+ V2 firmware, just to...
    Post by: AntiReality, Jan 9, 2019 in forum: Troubleshooting
  3. AntiReality
    Thread

    Answered Z Axis Triggered Issue

    After a hiatus of frustation involving the printer. I replaced the heated bed with a V2 and ordered some limit switches to replace the existing z...
    Thread by: AntiReality, Jan 9, 2019, 7 replies, in forum: Troubleshooting
  4. AntiReality
    Post

    Answered Z-Axis Runaway STL problem or R1+ Design Flaw?

    Think its likely that theres a fault in the files im trying to print?
    Post by: AntiReality, Apr 10, 2018 in forum: Troubleshooting
  5. AntiReality
    Thread

    Answered Z-Axis Runaway STL problem or R1+ Design Flaw?

    Ive been chugging away at some prints on my R1+ running Marlin 1.1.7 with UBL. PID Tuned/Z Offset and the obligatory G29 P1, G29 P3 T, G29 F10.0,...
    Thread by: AntiReality, Apr 10, 2018, 3 replies, in forum: Troubleshooting
  6. AntiReality
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Currently working off of my R1+ with UBL enabled 1.1.7 firmware. PID tuned the extruder and bed. Ive ran a G29 P1, G29 P3 T, G29 F10.0, G29 S1,...
    Post by: AntiReality, Mar 7, 2018 in forum: Mods and Upgrades
  7. AntiReality
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Are you issuing these commands via terminal, a configuration file, or using it in your slicer software as Gcode startup? What is the purpose of...
    Post by: AntiReality, Oct 2, 2017 in forum: Mods and Upgrades
  8. AntiReality
    Post

    Answered Robo3d R1+ Refurb Quirks

    I'm just surprised that theres so much play in the z leadscrews. I would think there would be more rigidity with the steppers below and the...
    Post by: AntiReality, Jul 16, 2017 in forum: Troubleshooting
  9. AntiReality
    Post

    Answered Robo3d R1+ Refurb Quirks

    I appreciate the help from everyone. Leveling out the one side helped the layers a bit and telling MC to add support everywhere helped with the...
    Post by: AntiReality, Jul 14, 2017 in forum: Troubleshooting
  10. AntiReality
    Post

    Answered Robo3d R1+ Refurb Quirks

    I just moved the right side threaded z-rod a minute ago as I was looking at my carriage and one side was lower than the other. Raised it up a bit....
    Post by: AntiReality, Jul 13, 2017 in forum: Troubleshooting
  11. AntiReality
    Post

    Answered Robo3d R1+ Refurb Quirks

    Appreciate the help. :) I took a zip tie and tied the wire loom back towards the top of the housing. I left the skirt to prime the extruder and...
    Post by: AntiReality, Jul 2, 2017 in forum: Troubleshooting
  12. AntiReality
    Thread

    Answered Robo3d R1+ Refurb Quirks

    Hello Everyone, I purchased a R1+ refurbed a couple months ago. Got around to using it recently. Seem to be having a couple issues with the...
    Thread by: AntiReality, Jun 29, 2017, 10 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again