1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Erica Lindström
    Post

    Trouble with z-offset

    Yes, I know. Even thoug I also do the fine tuning, the z-offset, during actual printing, becomes much higher than when finished with the fine...
    Post by: Erica Lindström, Nov 17, 2017 in forum: Troubleshooting
  2. Erica Lindström
    Thread

    Trouble with z-offset

    Recently when I do the z-offset it does not represent the correct distance between the hot end and the print bed. To get a appropriate z distance...
    Thread by: Erica Lindström, Nov 17, 2017, 3 replies, in forum: Troubleshooting
  3. Erica Lindström
    Post

    please HELP! print quality gone to hell.

    I have been doing exactly that for 3 days. The slip of paper is almost stuck under the extruder, I doubt I can position the print bed any closer...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  4. Erica Lindström
    Thread

    please HELP! print quality gone to hell.

    In the picture you can see a large green blob, it looks like a cat turd. 3 weeks ago I printed the gray item, its awesome! I tried to do that item...
    Thread by: Erica Lindström, Nov 9, 2017, 3 replies, in forum: Troubleshooting
  5. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Its just a tick in a box, can’t change the number of peripetiers. It is actually 2 counted when testning again. Still no luck. It looks so weird,...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  6. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Where do I change the perimeter? In Cura or in octo print? Cant find anything called terminal in octo print or Cura either. Im a total nincompoop...
    Post by: Erica Lindström, Nov 9, 2017 in forum: Troubleshooting
  7. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    I do that between every print with 95% alcohol.
    Post by: Erica Lindström, Nov 8, 2017 in forum: Troubleshooting
  8. Erica Lindström
    Post

    Whole first layer of print not sticking to print bed

    Sorry, just noticed that this post was in the wrong section, how do I move it to R2? Here's a picture any way...
    Post by: Erica Lindström, Nov 8, 2017 in forum: Troubleshooting
  9. Erica Lindström
    Thread

    Whole first layer of print not sticking to print bed

    I will go nuts soon, so I really hope the community can help me. The first layer of my current print is a square. The whole surface of the square...
    Thread by: Erica Lindström, Nov 8, 2017, 10 replies, in forum: Troubleshooting
  10. Erica Lindström
    Thread

    OctoPi upgrade?

    I use Cura for arranging my prints evenly on the surface of the bed. then I send it to the printer and press the button "go to Octo Print". A web...
    Thread by: Erica Lindström, Nov 8, 2017, 1 replies, in forum: General Questions
  11. Erica Lindström
    Post

    settings for RoboR2 in Cura?

    Thank you! I knew this was the place to get some answers.
    Post by: Erica Lindström, Aug 14, 2017 in forum: General Questions
  12. Erica Lindström
    Thread

    settings for RoboR2 in Cura?

    How am I supposed to fill in all the details for my printer in Cura? I just know the bed size (see picture). Show a picture on your settings or...
    Thread by: Erica Lindström, Aug 14, 2017, 3 replies, in forum: General Questions
  13. Erica Lindström
    Post

    How do I clear my filament jam?

    Thank you. Fixed it in a easyer way, but your reply gave me some hints on how to do it.
    Post by: Erica Lindström, Aug 3, 2017 in forum: Troubleshooting
  14. Erica Lindström
    Thread

    How do I clear my filament jam?

    In the picture you can see how I have pushed the new yellow filament through the cold end and there seems to be no jam there. In the extruder...
    Thread by: Erica Lindström, Aug 3, 2017, 2 replies, in forum: Troubleshooting
  15. Erica Lindström
    Post

    PLA Adhesion

    Awesome! I just tried this with my R2, since I had trouble with curling corners on big flat prints, and it worked like magic! Thank you, Thank...
    Post by: Erica Lindström, Jul 28, 2017 in forum: General Questions
  16. Erica Lindström
    Post

    Printer overextruding?

    Ok, thx. I only had my printer for a couple weeks (first 3D printer ever for me) and just started experimenting with it. I have managed to print...
    Post by: Erica Lindström, Jul 23, 2017 in forum: Troubleshooting
  17. Erica Lindström
    Post

    Printer overextruding?

    I let the R2 do it all since I know nothing about slicing or 3D printing.
    Post by: Erica Lindström, Jul 23, 2017 in forum: Troubleshooting
  18. Erica Lindström
    Thread

    Printer overextruding?

    I have a issue with a print from thingiverse I want to make. The file creator thinks my printer is overextruding. He suggests that I check that my...
    Thread by: Erica Lindström, Jul 23, 2017, 7 replies, in forum: Troubleshooting
  19. Erica Lindström
    Post

    Error connecting to wi-fi and whistling noise

    For the love of my life, I can't get my printer to connect to my wi-fi. Been running around and moving it all over the place and now it stands 2m...
    Post by: Erica Lindström, Jul 21, 2017 in forum: Troubleshooting
  20. Erica Lindström
    Post

    Rod supposed to be moving up and down?

    Mine was not like your video. My rod actually was loose at the back end. I just popped it back to place.
    Post by: Erica Lindström, Jul 21, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 26 Next >
Search Again
Page 1 of 2