1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. milw
    Post

    Repurposing Pirate3d Buccaneer

    Has anyone made a Marlin config file yet? I'm just getting my Ramps 1.4 hooked up, so that'll be the next step. Whoops, just read the updates to...
    Post by: milw, Feb 23, 2018 in forum: Off Topic
  2. milw
    Post

    Repurposing Pirate3d Buccaneer

    unknown, there was no response when i tried them with printer on. Maybe following the traces would give a clue? Sent from my iPhone using Tapatalk
    Post by: milw, Dec 29, 2017 in forum: Off Topic
  3. milw
    Post

    Repurposing Pirate3d Buccaneer

    Here's a link to 0.9.8! Let me know if you can't get it. https://www.dropbox.com/s/pudeqpv5f71girx/Buccaneer-0.9.8.zip?dl=0
    Post by: milw, Dec 23, 2017 in forum: Off Topic
  4. milw
    Post

    Repurposing Pirate3d Buccaneer

    Yes I tried some obvious combos, but without source code I think it’d be really difficult to change how it works, like the horrid web interface....
    Post by: milw, Dec 17, 2017 in forum: Off Topic
  5. milw
    Post

    Repurposing Pirate3d Buccaneer

    I asked them to open source it but no go. You can try logging in to the controller, i got an ssh terminal response but no clue as to...
    Post by: milw, Dec 17, 2017 in forum: Off Topic
  6. milw
    Post

    Repurposing Pirate3d Buccaneer

    Well, the original power supply is rated 19V 4.7A dc, so might want to be rated over 7A at 12V. Another thought, a breakout board to allow using...
    Post by: milw, Sep 17, 2017 in forum: Off Topic
  7. milw
    Post

    Repurposing Pirate3d Buccaneer

    Unfortunately I haven't built the cable converter for the head yet- we also need to work out a mounting method for the control board and a...
    Post by: milw, Sep 15, 2017 in forum: Off Topic
  8. milw
    Post

    Repurposing Pirate3d Buccaneer

    [IMG] Here's the top of the board. Looks like an Atmega128 is actually running the steppers. I figure if this helps anyone else, its not wasted...
    Post by: milw, Jul 31, 2017 in forum: Off Topic
  9. milw
    Post

    Repurposing Pirate3d Buccaneer

    It's definitely of their own design, though the 'brain' is a Cubie A20 board booting off a custom memery chip. I'll post a pic tonight, but its a...
    Post by: milw, Jul 31, 2017 in forum: Off Topic
  10. milw
    Thread

    Repurposing Pirate3d Buccaneer

    So I was one of the 'lucky' few who actually received a printer, about 2 years after funding the kickstarter. I have managed to print some nice...
    Thread by: milw, Jul 29, 2017, 104 replies, in forum: Off Topic
  11. milw
    Post

    Solved Thermistor on heated bed is open

    Awesome, thanks! Sent from my iPhone using Tapatalk
    Post by: milw, Jul 21, 2017 in forum: Troubleshooting
  12. milw
    Post

    Solved Thermistor on heated bed is open

    Yup. Broken lead right where it was taped to the bed. I had played with some smaller heater elements on a different printer, but they had the RTD...
    Post by: milw, Jul 21, 2017 in forum: Troubleshooting
  13. milw
    Post

    Solved Thermistor on heated bed is open

    Well, MC reports it as RoBo 3D R1 V5 if that's helpful.
    Post by: milw, Jul 21, 2017 in forum: Troubleshooting
  14. milw
    Post

    Solved Thermistor on heated bed is open

    I'm running MC on Mac OSX, is there a firmware reading command?
    Post by: milw, Jul 21, 2017 in forum: Troubleshooting
  15. milw
    Thread

    Solved Thermistor on heated bed is open

    hi, I bought a used original Robo 3D ( a modded kickstarter one), and had the heated bed working nicely with PLA. But during a long print when I...
    Thread by: milw, Jul 21, 2017, 11 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again