1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. J0ester
    Post

    problem with robo OS2.0

    this always happen when i on my printer and done my first print..
    Post by: J0ester, Mar 24, 2018 in forum: Troubleshooting
  2. J0ester
    Thread

    problem with robo OS2.0

    hi any one having this problem when printing is start i receive an error msg. at this two point . but after reset it i can print normally..:(
    Thread by: J0ester, Mar 23, 2018, 2 replies, in forum: Troubleshooting
  3. J0ester
    Post

    Extruder tensioner arm

    pls model for me..thank alot
    Post by: J0ester, Nov 29, 2017 in forum: Show and Tell
  4. J0ester
    Post

    Extruder tensioner arm

    thank alot.. my i cant print as my printer is down too.
    Post by: J0ester, Nov 28, 2017 in forum: Show and Tell
  5. J0ester
    Post

    Extruder tensioner arm

    ok thank. than just have to send mi the replacement unit.
    Post by: J0ester, Nov 27, 2017 in forum: Show and Tell
  6. J0ester
    Post

    Extruder tensioner arm

    anyone have the stl File for this?
    Post by: J0ester, Nov 27, 2017 in forum: Show and Tell
  7. J0ester
    Thread

    Extruder tensioner arm

    hi anyone can help my extruder tensioner arm have broke into 2 pieces[ATTACH]
    Thread by: J0ester, Nov 27, 2017, 16 replies, in forum: Show and Tell
  8. J0ester
    Post

    After changing new pogo adapter .

    thank alot alr arrange for tier 2 to call back. hope i can finish my print before the dead line
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  9. J0ester
    Post

    After changing new pogo adapter .

    i remove the bed cable connector from the main board and it still show the same msg.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  10. J0ester
    Post

    After changing new pogo adapter .

    switch back the old pin still have the same msg..:(
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  11. J0ester
    Post

    After changing new pogo adapter .

    i think ther is a short after i install the new pin. after tat the printer restart itself thn the msg appears.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  12. J0ester
    Post

    After changing new pogo adapter .

    once i on my printer it show this msg straight.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  13. J0ester
    Post

    After changing new pogo adapter .

    new pogo adaptar
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  14. J0ester
    Post

    After changing new pogo adapter .

    noted.. thank very much
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  15. J0ester
    Post

    After changing new pogo adapter .

    yep.. i even try remove the cable from the main board.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  16. J0ester
    Post

    After changing new pogo adapter .

    both bed n ext show off. i cant on it.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  17. J0ester
    Post

    After changing new pogo adapter .

    when i on the printer it show mi the error msg. i can even go into the menu.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  18. J0ester
    Post

    After changing new pogo adapter .

    all connection, fuse check nothing abnormal.
    Post by: J0ester, Sep 28, 2017 in forum: Troubleshooting
  19. J0ester
    Thread

    After changing new pogo adapter .

    MAXTEMP triggered, system stopped! Heater_ID: bed !! can anyone help?
    Thread by: J0ester, Sep 27, 2017, 24 replies, in forum: Troubleshooting
  20. J0ester
    Thread

    bearings problem

    anyone have bearings issue?
    Thread by: J0ester, Aug 27, 2017, 3 replies, in forum: Troubleshooting
Showing results 1 to 20 of 20
Search Again