1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Ok, ill try that I had offset at like +10mm and it was still low. Thanks
    Post by: jayden17, Dec 14, 2018 in forum: Mods and Upgrades
  2. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    UPDATE: I had very ugly prints ,shifting and a couple other problems so I think I did not configure it correctly so I switched to marlin...
    Post by: jayden17, Dec 14, 2018 in forum: Mods and Upgrades
  3. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Jamming gone but I appear to have a very large amount of over extrusion im sure its just a setting I missed
    Post by: jayden17, Aug 31, 2018 in forum: Mods and Upgrades
  4. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    oops yes I actually wired it into one of fan pins. I can get firmware and take some pics later. But if jamming gone I should be good
    Post by: jayden17, Aug 29, 2018 in forum: Mods and Upgrades
  5. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Still working at it. jams every print for some reason. The cooling fan doesn't run automatically either. I copied and switch board from...
    Post by: jayden17, Aug 28, 2018 in forum: Mods and Upgrades
  6. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    nevermind its fixed now
    Post by: jayden17, Aug 8, 2018 in forum: Mods and Upgrades
  7. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    I have been trying to do z on probe plug using middle 2 maybe It doesn't work that way:confused:
    Post by: jayden17, Aug 8, 2018 in forum: Mods and Upgrades
  8. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Endstop pins were not properly configured https://reprap.org/forum/read.php?415,812958. Fixed that issue Z still triggered before hitting bed. And...
    Post by: jayden17, Aug 8, 2018 in forum: Mods and Upgrades
  9. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    With my experience with this board that is definitely an major advantage.
    Post by: jayden17, Aug 8, 2018 in forum: Mods and Upgrades
  10. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Sounds super familiar. They seem to be stuck in the same place I am:(. I don't know what i'm missing. My main problem is there is very little...
    Post by: jayden17, Aug 8, 2018 in forum: Mods and Upgrades
  11. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Everything except endstops work now.
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  12. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Ahhhh ok thats makes sense.
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  13. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Looked through documentation and found that I had screen wired incorrectly...
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  14. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Thanks, but already added an octopi. I am curious how you mounted your camera(if you added one) since I don't have a mount yet. If you could link...
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  15. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    :oops:Maybe I should of stuck with RAMPS. I would still like to see if I can get my einsy to work just for the features it could add. However, if...
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  16. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    I thought it would be an upgrade from RAMPS. Are these boards usually unreliable??? So far I have not had good luck. I know it can be setup to not...
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  17. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Update: Still have not figured out endstops after enabling sd support screen keeps blinking. Motors seemed to have completely quit.
    Post by: jayden17, Aug 7, 2018 in forum: Mods and Upgrades
  18. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Ok fixed leveling thanks.
    Post by: jayden17, Aug 6, 2018 in forum: Mods and Upgrades
  19. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Ok, I have added my newest configuration and the pins file on top. by the way code won't compile after adding leveling getting this error #error...
    Post by: jayden17, Aug 6, 2018 in forum: Mods and Upgrades
  20. jayden17
    Post

    Robo3d r1+ Einsy firmware help

    Ok, Thanks wasn't quite sure what to look for the auto leveling before. I do have a graphical display connected but I may not have connected it...
    Post by: jayden17, Aug 6, 2018 in forum: Mods and Upgrades
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2