1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jaak Ahelik
    Post

    Cooldown

    There was a smallll piece and it solved the problem, it was really smallll, THX
    Post by: Jaak Ahelik, Dec 14, 2017 in forum: Troubleshooting
  2. Jaak Ahelik
    Post

    Cooldown

    The screen is clean, but also the delete and set buttons are blinking
    Post by: Jaak Ahelik, Dec 14, 2017 in forum: Troubleshooting
  3. Jaak Ahelik
    Post

    Cooldown

    No, I did not, and it dont go away also
    Post by: Jaak Ahelik, Dec 14, 2017 in forum: Troubleshooting
  4. Jaak Ahelik
    Thread

    Cooldown

    Why do I get this screen in the middle of printing?
    Thread by: Jaak Ahelik, Dec 14, 2017, 6 replies, in forum: Troubleshooting
  5. Jaak Ahelik
    Post

    system stopped! Heater_ID: bed

    Can I bypass the heated bed? I need to print some stuff?
    Post by: Jaak Ahelik, Oct 16, 2017 in forum: Troubleshooting
  6. Jaak Ahelik
    Post

    system stopped! Heater_ID: bed

    Not just one pin, but two pins. does it happen often?
    Post by: Jaak Ahelik, Oct 16, 2017 in forum: Troubleshooting
  7. Jaak Ahelik
    Post

    system stopped! Heater_ID: bed

    One of the pins on the left seems to be lower then others
    Post by: Jaak Ahelik, Oct 16, 2017 in forum: Troubleshooting
  8. Jaak Ahelik
    Post

    system stopped! Heater_ID: bed

    Robo R2
    Post by: Jaak Ahelik, Oct 16, 2017 in forum: Troubleshooting
  9. Jaak Ahelik
    Thread

    system stopped! Heater_ID: bed

    Unhandled communication error The was an unhandled error while talking to the printer. Due to that OctoPrint disconnected. Error: Heating failed,...
    Thread by: Jaak Ahelik, Oct 16, 2017, 10 replies, in forum: Troubleshooting
  10. Jaak Ahelik
    Post

    Filament Has Run Out

    Everything works fine, thanks again, problem solved
    Post by: Jaak Ahelik, Sep 30, 2017 in forum: Troubleshooting
  11. Jaak Ahelik
    Post

    Filament Has Run Out

    Thanks a lot. I uninstalled the sensor plugin and now it has been printing for 25 min without problem, let see how far it goes.
    Post by: Jaak Ahelik, Sep 30, 2017 in forum: Troubleshooting
  12. Jaak Ahelik
    Post

    Filament Has Run Out

    Post by: Jaak Ahelik, Sep 30, 2017 in forum: Troubleshooting
  13. Jaak Ahelik
    Post

    Filament Has Run Out

    Everything is correct, but still got the message, when doing the wizard, it loads, starting to print it stops?
    Post by: Jaak Ahelik, Sep 30, 2017 in forum: Troubleshooting
  14. Jaak Ahelik
    Thread

    Filament Has Run Out

    Why do I get this message after every 10 sec?
    Thread by: Jaak Ahelik, Sep 30, 2017, 26 replies, in forum: Troubleshooting
  15. Jaak Ahelik
    Post

    Extruder Home Position

    Thx, I'll try it tonight Thank you, problem solved.
    Post by: Jaak Ahelik, Sep 10, 2017 in forum: Troubleshooting
  16. Jaak Ahelik
    Post

    Extruder Home Position

    Those two parts get too close. There is no distance between. They start vibrate.
    Post by: Jaak Ahelik, Sep 10, 2017 in forum: Troubleshooting
  17. Jaak Ahelik
    Thread

    Extruder Home Position

    [ATTACH] Before to print, the extruder makes terrible noise at home position, how to change the position? Those two parts are too close to each...
    Thread by: Jaak Ahelik, Sep 10, 2017, 5 replies, in forum: Troubleshooting
  18. Jaak Ahelik
    Post

    Noise

    To save time, can you give me advice how to set it. Thx
    Post by: Jaak Ahelik, Sep 9, 2017 in forum: Troubleshooting
  19. Jaak Ahelik
    Thread

    Noise

    Before the extruder starts to move, it makes terrible noise (in left corner)? [MEDIA] Metal backplate is connected to the plastic, how to...
    Thread by: Jaak Ahelik, Sep 9, 2017, 3 replies, in forum: Troubleshooting
  20. Jaak Ahelik
    Thread

    Z offset

    robo 3d r2 when unboxed, the z-offset nozzle moves to the left corner?
    Thread by: Jaak Ahelik, Aug 22, 2017, 1 replies, in forum: Troubleshooting
Showing results 1 to 20 of 20
Search Again