1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. UltimaA380
    Post

    Solved Wierd print issues..

    Changing it to -0.75 fixed it. Thanks!
    Post by: UltimaA380, Apr 16, 2018 in forum: Troubleshooting
  2. UltimaA380
    Post

    Solved Wierd print issues..

    My start gcode is G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp and wait G28 X0 Y0 Z0 ; Home...
    Post by: UltimaA380, Apr 14, 2018 in forum: Troubleshooting
  3. UltimaA380
    Post

    Solved Wierd print issues..

    Also should mention I am using MatterControl as Cura seemed to have slightly worse results.
    Post by: UltimaA380, Apr 14, 2018 in forum: Troubleshooting
  4. UltimaA380
    Thread

    Solved Wierd print issues..

    I am trying to print a small part, and on the underside its very messy however on the top it is fairly clean. I am using IC3D Grey 1.75mm PLA...
    Thread by: UltimaA380, Apr 14, 2018, 8 replies, in forum: Troubleshooting
  5. UltimaA380
    Post

    Solved R1+ not homing

    I think it's just magically go away, thank you!
    Post by: UltimaA380, Dec 13, 2017 in forum: Troubleshooting
  6. UltimaA380
    Post

    Solved R1+ not homing

    I'm confused.. this is the start of the gcode: ;FLAVOR:RepRap ;TIME:90846 ;Filament used: 54.1589m ;Layer height: 0.1 ;Generated with...
    Post by: UltimaA380, Dec 13, 2017 in forum: Troubleshooting
  7. UltimaA380
    Post

    Solved R1+ not homing

    I reset my machines settings before I changed the gcode.. so maybe its from that.. but do you know what would make it do that? Like the gear moves...
    Post by: UltimaA380, Dec 13, 2017 in forum: Troubleshooting
  8. UltimaA380
    Post

    Solved R1+ not homing

    Didn't do it before changing start gcode.. retrac distance is 1.5mm
    Post by: UltimaA380, Dec 13, 2017 in forum: Troubleshooting
  9. UltimaA380
    Post

    Solved R1+ not homing

    @mark tomlinson Seems to autolevel now, but it pulls the filament back out of the extruder like.. 10cm? wth?
    Post by: UltimaA380, Dec 13, 2017 in forum: Troubleshooting
  10. UltimaA380
    Thread

    Solved R1+ not homing

    So I found some start gcode to make my r1+ home with cura but now I lost it.. just prints in the air and doesntrr autolevel. gcode: G92 E0 ;...
    Thread by: UltimaA380, Dec 13, 2017, 10 replies, in forum: Troubleshooting
  11. UltimaA380
    Thread

    Answered Blobs around print.

    Got some new filament, prints great except for some parts. I dont think its the filament itself because someone sent me a picture using the same...
    Thread by: UltimaA380, Nov 4, 2017, 2 replies, in forum: Troubleshooting
  12. UltimaA380
    Post

    Solved Bent my lead screw :(

    Would this config be what youre talking about?
    Post by: UltimaA380, Nov 1, 2017 in forum: Troubleshooting
  13. UltimaA380
    Post

    Solved Bent my lead screw :(

    Ok, any suggestions for which to buy?
    Post by: UltimaA380, Oct 31, 2017 in forum: Troubleshooting
  14. UltimaA380
    Post

    Solved Bent my lead screw :(

    Hmm, I watched a video of some one doing it and I'm thinking of doing that now, (although my printed stabilizers might've removed it all together,...
    Post by: UltimaA380, Oct 31, 2017 in forum: Troubleshooting
  15. UltimaA380
    Post

    Solved Bent my lead screw :(

    Thanks for your speedy answer, see you everywhere on the forums. I will definitely try bending the leadscrew back (have a vise I can try to do it...
    Post by: UltimaA380, Oct 30, 2017 in forum: Troubleshooting
  16. UltimaA380
    Thread

    Solved Bent my lead screw :(

    HOUSTON HAS A PROBLEM ROBO3D R1+ So, the printer has been sitting for a while and I decided I'd like to use it again, then while trying I...
    Thread by: UltimaA380, Oct 30, 2017, 12 replies, in forum: Troubleshooting
Showing results 1 to 16 of 16
Search Again