1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Rod Smith
    Thread

    What type of electrical connector does the heated bed use?

    I'm planning to replace my Robo3D R1+'s heated bed with a new aluminum one. I've already got most of the components I need, but I'm having trouble...
    Thread by: Rod Smith, Dec 29, 2020, 3 replies, in forum: Mods and Upgrades
  2. Rod Smith
    Thread

    Robo3D R1+ Motherboard Upgrade: SKR Pro plus RepRapFirmware

    I've recently done some major surgery on my Robo3D R1+, pulling out the 8-bit Arduino+RAMPS control board and replacing it with a 32-bit...
    Thread by: Rod Smith, Nov 30, 2020, 4 replies, in forum: Mods and Upgrades
  3. Rod Smith
    Thread

    Partially Solved Ugly overhang

    Here's my latest problem: [IMG] This photo is of a print of this temperature tower from Thingiverse. Compared to the photos of the same object...
    Thread by: Rod Smith, Nov 28, 2017, 5 replies, in forum: Troubleshooting
  4. Rod Smith
    Thread

    Linux software for the Robo 3D R1+ (and other 3D printers)

    It's been two weeks since I received my Robo 3D R1+ printer. When I asked on this forum about Linux support, I received little in the way of...
    Thread by: Rod Smith, Nov 25, 2017, 2 replies, in forum: Software
  5. Rod Smith
    Thread

    Solved What to lubricate for Z-axis squealing noise?

    I've had my R1+ for two weeks now, and it's developed an annoying squealing noise when the head moves vertically (z-axis). To be sure, it still...
    Thread by: Rod Smith, Nov 24, 2017, 4 replies, in forum: Troubleshooting
  6. Rod Smith
    Thread

    Black Friday/Cyber Monday deals....

    If you need to buy filament in the USA, today (Friday the 24th) seems to be the day. I just ordered some from MakerGeeks for 30% off (coupon code:...
    Thread by: Rod Smith, Nov 24, 2017, 18 replies, in forum: Off Topic
  7. Rod Smith
    Thread

    Partially Solved Z axis setting (M565): Correct now?

    Over in this thread, I got some advice from mark tomlinson on adjusting my Z-axis value via the M565 g-code command. Thanks for that! I've now...
    Thread by: Rod Smith, Nov 14, 2017, 2 replies, in forum: Troubleshooting
  8. Rod Smith
    Thread

    Answered Filament best practices between print sessions

    Being new to 3D printing, I'm still learning the basics, including things that seem to be omitted from all the tutorials I've found online. One of...
    Thread by: Rod Smith, Nov 13, 2017, 3 replies, in forum: General Questions
  9. Rod Smith
    Thread

    Answered R1+ printer sometimes ejecting filament before print

    I received my Robo 3D R1+ on Friday, did a couple of test prints from macOS using MatterControl, and then hooked up a Raspberry Pi and began...
    Thread by: Rod Smith, Nov 12, 2017, 15 replies, in forum: Troubleshooting
  10. Rod Smith
    Thread

    Solved Newbie with two questions/problems....

    Hi, I received my new Robo 3D R1+ earlier today, and I've been setting it up and doing some prints with it. In the process of this, I've run into...
    Thread by: Rod Smith, Nov 10, 2017, 3 replies, in forum: Troubleshooting
  11. Rod Smith
    Thread

    Questions about Robo 3D R1+

    Hi, I'm considering buying my first 3D printer, and the Robo 3D R1+ seems like a great value because of its bigger build volume compared to other...
    Thread by: Rod Smith, Nov 7, 2017, 10 replies, in forum: General Questions
Showing results 1 to 11 of 11
Search Again