1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. mheath82
    Post

    Solved C2 X axis belt tension

    So as it turns out it was not the belt causing the issue at all. The X axis rod closest to the front of the printer needed some serious cleaning...
    Post by: mheath82, Apr 4, 2018 in forum: Troubleshooting
  2. mheath82
    Post

    Solved C2 X axis belt tension

    Pic:
    Post by: mheath82, Apr 2, 2018 in forum: Troubleshooting
  3. mheath82
    Thread

    Solved C2 X axis belt tension

    I received a replacement C2 after all kinds of levelling issues with my store bought machine and have had good luck with it until now. It hasn't...
    Thread by: mheath82, Apr 2, 2018, 6 replies, in forum: Troubleshooting
  4. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    Just wanted to add an update for those reading or having similar issues. Robo agreed to replace my C2 with a new one. I have since received it and...
    Post by: mheath82, Feb 9, 2018 in forum: Troubleshooting
  5. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    I've still been back and fourth with Robo about the aluminium print bed frame being warped and am absolutely appalled at the response I received...
    Post by: mheath82, Jan 15, 2018 in forum: Troubleshooting
  6. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    Well the BuildTak did wonders for the adhesion. I'm still having an issue on the right side on the corners but it is much better than it was.
    Post by: mheath82, Jan 11, 2018 in forum: Troubleshooting
  7. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    I really appreciate the offer @OutsourcedGuru but at this point Robo's official answer to my warped print bed frame thing was 'We are not sure...
    Post by: mheath82, Dec 27, 2017 in forum: Troubleshooting
  8. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    So I was in the process of doing this and I believe I found the problem. The aluminium frame that the print bed sits on is bowed. I put a straight...
    Post by: mheath82, Dec 22, 2017 in forum: Troubleshooting
  9. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    I tried printing it with various settings. Seems I need to use a raft or it just warps on the first bead of filament and then the nozzle just runs...
    Post by: mheath82, Dec 20, 2017 in forum: Troubleshooting
  10. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    Thank you Mark and OutsourcedGuru. These are excellent tips! On a side note, after checking to see if my print bed is level, I've also noticed...
    Post by: mheath82, Dec 18, 2017 in forum: Troubleshooting
  11. mheath82
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    Sorry, yes PLA. It's printing at 195c. I have not printed the temperature test tower but will do that. I just found it odd that it only curls at...
    Post by: mheath82, Dec 17, 2017 in forum: Troubleshooting
  12. mheath82
    Thread

    Solved Bed Adhesion, I'm about at my whits end.

    I've had the C2 for a little over a month now. I've been able to make some high quality smaller prints after some tweaking but am having nothing...
    Thread by: mheath82, Dec 17, 2017, 23 replies, in forum: Troubleshooting
  13. mheath82
    Thread

    Solved Unable to delete files/logs from Octoprint web interface

    Hi all, I recently upgraded my C2 with a 32GB micro SD using an image provided by Robo support. While printing works fine I can't seem to remove...
    Thread by: mheath82, Dec 15, 2017, 3 replies, in forum: Troubleshooting
  14. mheath82
    Post

    Solved Out-of-box Robo C2 microSD image

    Thank you for the insight. I actually ended up using robodobo's approach and contacted Robo support for an image. Oddly enough with their image...
    Post by: mheath82, Dec 11, 2017 in forum: Software
  15. mheath82
    Post

    Solved Out-of-box Robo C2 microSD image

    I'm a new C2 owner and have been doing some tweaking of my printer. I've added the Pi Camera and it has been working with the SD it was shipped...
    Post by: mheath82, Dec 5, 2017 in forum: Software
Showing results 1 to 15 of 15
Search Again