1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jordan Weinrich
    Post

    Unanswered Robo3d R1+ Bed Replacement/y-Carriage Replacement

    I think I am probably going to stick with Marlin for now. I don't feel like learning how to do everything in RRF because I have spent a lot of...
    Post by: Jordan Weinrich, Dec 18, 2020 in forum: Troubleshooting
  2. Jordan Weinrich
    Post

    Unanswered Robo3d R1+ Bed Replacement/y-Carriage Replacement

    I've seen those youtube videos before and I jus am not a fan of the rails being attached to the bed because each rail feels very heavy, like at...
    Post by: Jordan Weinrich, Dec 18, 2020 in forum: Troubleshooting
  3. Jordan Weinrich
    Thread

    Unanswered Robo3d R1+ Bed Replacement/y-Carriage Replacement

    Hi, the heated glass bed finally cracked on me. I have a few modifications that I am considering making to the printer. Current Upgrades: E3D v6...
    Thread by: Jordan Weinrich, Dec 18, 2020, 5 replies, in forum: Troubleshooting
  4. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    I've got it all figured out and working. I have for about a week or so and everything is good. I'm just trying to get linear advance down now...
    Post by: Jordan Weinrich, Jan 28, 2020 in forum: Software
  5. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    Okay... New update!!! I went into the configuration_store.cpp file and declared the float "JUNCTION_DEVIATION_MM" the line above...
    Post by: Jordan Weinrich, Jan 16, 2020 in forum: Software
  6. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    Well I have the newest version of the compiler and now I am receiving different errors. Arduino: 1.8.10 (Windows 10), Board: "Arduino/Genuino...
    Post by: Jordan Weinrich, Jan 16, 2020 in forum: Software
  7. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    I am on the old compiler. Poops... Will I have to undo my changes? I think I kept track of all of them.
    Post by: Jordan Weinrich, Jan 16, 2020 in forum: Software
  8. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    I got error messages such as " filament_unload_retract_length is now filament_unload_purge_retract" 3 or 4 times and then this one which I don't...
    Post by: Jordan Weinrich, Jan 16, 2020 in forum: Software
  9. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    I have downloaded Marlin 2.0 directly from github but have not tried merging them yet so I will try that and let you know how it goes!
    Post by: Jordan Weinrich, Jan 15, 2020 in forum: Software
  10. Jordan Weinrich
    Post

    Robo3d R1+ Marlin 2.0

    I copied the error messages. Arduino: 1.6.9 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"...
    Post by: Jordan Weinrich, Jan 15, 2020 in forum: Software
  11. Jordan Weinrich
    Thread

    Robo3d R1+ Marlin 2.0

    Okay so I am trying to switch over to marlin 2.0 and could not figure out where to start or how to do this. I found this thread:...
    Thread by: Jordan Weinrich, Jan 13, 2020, 21 replies, in forum: Software
  12. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    Okay. I contacted them and explained the issue along with a few screenshots of the temperature graphs and hopefully they will send a replacement...
    Post by: Jordan Weinrich, Feb 8, 2019 in forum: Troubleshooting
  13. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    Well its a new e3d amp that i got from matterhackers.com, i just installed it and havent even printed anything with it because ive had issues the...
    Post by: Jordan Weinrich, Feb 8, 2019 in forum: Troubleshooting
  14. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    It was doing good and reading the correct temperature for a while so i heated up the extruder and the temperature was fine. I turned it off and...
    Post by: Jordan Weinrich, Feb 8, 2019 in forum: Troubleshooting
  15. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    I havent changed anything and currently it is reading 19c, which is about the same as what the bed temperature is reading at right now. I tried...
    Post by: Jordan Weinrich, Feb 8, 2019 in forum: Troubleshooting
  16. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    im aware. i have the amplifier board. I placed the old temperature sensor in the old spot it was originally in and it worked fine. when i switched...
    Post by: Jordan Weinrich, Feb 7, 2019 in forum: Troubleshooting
  17. Jordan Weinrich
    Post

    Answered PT100 Temperature Reading Fluctuating

    I uploaded the original firmware and plugged in the old thermistor and it read properly. I also took out the wires from the board and it still...
    Post by: Jordan Weinrich, Feb 7, 2019 in forum: Troubleshooting
  18. Jordan Weinrich
    Thread

    Answered PT100 Temperature Reading Fluctuating

    Hi, I recently replaced the temp sensor i had with a pt100, using the amplifier board and following the instructions from a thread on here. It is...
    Thread by: Jordan Weinrich, Feb 7, 2019, 14 replies, in forum: Troubleshooting
  19. Jordan Weinrich
    Post

    Solved E3d pt100 problems.

    Im having the same problem. Did you find a solution?
    Post by: Jordan Weinrich, Feb 7, 2019 in forum: Troubleshooting
Showing results 1 to 19 of 19
Search Again