1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Salvatore Lacorte
    Thread

    New dual extrusion upgrade kit

    Hello everyone. Noticed many of you have been wanting to turn your robo 3d R1 + printer dual extrusion but had not know how or been able to. Today...
    Thread by: Salvatore Lacorte, Apr 3, 2019, 0 replies, in forum: Mods and Upgrades
  2. Salvatore Lacorte
    Thread

    Solved arduino gets hot and powers off ramps

    I will turn on my arduino for about 20 seconds and the screen powers up and displays information. then the information will disappear and im...
    Thread by: Salvatore Lacorte, Apr 21, 2018, 15 replies, in forum: Troubleshooting
  3. Salvatore Lacorte
    Thread

    Answered ramps 1.4 blinks orange then stops working

    I just loaded up my printer and tried to test the x axis and then it happened. It blinked orange and stopped working. I then restarted and it...
    Thread by: Salvatore Lacorte, Apr 20, 2018, 12 replies, in forum: Troubleshooting
  4. Salvatore Lacorte
    Thread

    Solved drivers Wont work

    I tried to add the chimera to my robo 3d r1 Plus but I am encountering a problem where certain types of drivers wont allow information to be...
    Thread by: Salvatore Lacorte, Apr 20, 2018, 13 replies, in forum: Troubleshooting
  5. Salvatore Lacorte
    Thread

    Driver wont work HELP!!1

    I have been working on my robo for a while and i am stuck because my drivers wont allow my motors to move freely. One motor wont move and the...
    Thread by: Salvatore Lacorte, Apr 16, 2018, 2 replies, in forum: Troubleshooting
  6. Salvatore Lacorte
    Thread

    Answered Can you replace ramps 1.4

    I have been having lots of trouble with my ramps 1.4 and mega. Can I replace the controller board with an mks base 1.4 I have had enough problems...
    Thread by: Salvatore Lacorte, Apr 16, 2018, 1 replies, in forum: Troubleshooting
  7. Salvatore Lacorte
    Thread

    Help needed with robo 3d chimera upgrade

    Today I have upgraded to the chimera and in my last thread we adressed the issue with the broken stepper drivers. I have it all hooked up and...
    Thread by: Salvatore Lacorte, Apr 12, 2018, 5 replies, in forum: Troubleshooting
  8. Salvatore Lacorte
    Thread

    Answered arduino won't connect to computer when ramps installed.

    Today I have been working on connecting the Chimera to my robo 3D R1+. I bought a new ramps board and attached that to my arduino mega. I have it...
    Thread by: Salvatore Lacorte, Apr 11, 2018, 21 replies, in forum: Troubleshooting
  9. Salvatore Lacorte
    Thread

    Firmware for chimera on R1 plus

    I have been working on the firmware but am stuck. When i power it on all that happens is i hear a slight squeak and nothing else. I hope this is a...
    Thread by: Salvatore Lacorte, Apr 8, 2018, 0 replies, in forum: Troubleshooting
  10. Salvatore Lacorte
    Thread

    How to wire dual extrusion on robo 3D R1 +

    I have been stuck working on my chimera upgrade on my robo. I have everything setup except the print cooling fans and the led. I don't know where...
    Thread by: Salvatore Lacorte, Apr 8, 2018, 10 replies, in forum: Troubleshooting
Showing results 1 to 10 of 10
Search Again