1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Larrydoodoo
    Post

    Solved A4988 to DVR2588

    The problem where X stops shy of its end stop is resolved. The drv8825 drivers are new Sent from my SM-G965U using Tapatalk
    Post by: Larrydoodoo, Oct 9, 2019 in forum: Troubleshooting
  2. Larrydoodoo
    Post

    Solved A4988 to DVR2588

    Sorry it took so long to reply. An update on my issue... since my last reply to this thread, I've replaced the motherboard with a ramps 1.6 board....
    Post by: Larrydoodoo, Oct 9, 2019 in forum: Troubleshooting
  3. Larrydoodoo
    Thread

    Solved R1 plus stepper motor wire color diagram

    Anyone have a wire color diagram for the stepper motors for the R1 plus? Thanks in advance.
    Thread by: Larrydoodoo, Oct 9, 2019, 4 replies, in forum: Troubleshooting
  4. Larrydoodoo
    Post

    Solved A4988 to DVR2588

    Im using the board that came with the robo
    Post by: Larrydoodoo, Sep 26, 2019 in forum: Troubleshooting
  5. Larrydoodoo
    Thread

    Solved A4988 to DVR2588

    When replacing the stepper drivers, does anything in the firmware need to be modified? My printer is acting funny... when I run a g20, it probes...
    Thread by: Larrydoodoo, Sep 26, 2019, 9 replies, in forum: Troubleshooting
  6. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    Everything is working correctly at the moment. Thanks for all the help Sent from my LG-H830 using Tapatalk
    Post by: Larrydoodoo, May 28, 2018 in forum: Troubleshooting
  7. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    I have everything almost worked out. Heater core had bad wiring from the factory so I rewired it and working fine. LCD is working great, was able...
    Post by: Larrydoodoo, May 26, 2018 in forum: Troubleshooting
  8. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    Here's an update. I haven't uploaded the v2 firmware as of yet. I wanted to try and use cura instead of MC. I press preheat for the extruder, and...
    Post by: Larrydoodoo, May 25, 2018 in forum: Troubleshooting
  9. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    I will definitely give it another try with these files. I tried for what seemed like forever last night to upload. Ill post the outcome when I get...
    Post by: Larrydoodoo, May 25, 2018 in forum: Troubleshooting
  10. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    I'm having issues trying to flash the v2 firmware. In the zip file there are 2 .ino files. Marlin and robo3dv2. Sent from my LG-H830 using Tapatalk
    Post by: Larrydoodoo, May 25, 2018 in forum: Troubleshooting
  11. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    not getting any voltage to heater core or cooling fan...tested with 2 ramps boards. maybe ive shorted out the arduino??
    Post by: Larrydoodoo, May 24, 2018 in forum: Troubleshooting
  12. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    I added the library. I currently have the v1 firmware and I'm trying to flash the v2 Sent from my LG-H830 using Tapatalk
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  13. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    Arduino: 1.8.5 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from...
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  14. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    i use my laptop. when pre heat is initiated, the lights on the ramps light up as if its working. ill check again when i get home with the multimeter
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  15. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    ive tried other heater cores from other extruders, one of them being stock. also the same result from the stock robo ramps and also the knock off...
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  16. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    please forgive me for my lack of detail, im sure its obvious that i dont do this often. i get no heat what so ever when initiated, both heat bed...
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  17. Larrydoodoo
    Post

    Solved getting nothing after replacing extruder

    yes, it is a knock off. ive tried other heaters from my other extruders that i have and still get nothing also with multiple wiring...
    Post by: Larrydoodoo, May 23, 2018 in forum: Troubleshooting
  18. Larrydoodoo
    Thread

    Solved getting nothing after replacing extruder

    hello all, i bought this printer used and im very pleased thus far. I was having issues with the stock extruder, so i decided to chane it out. i...
    Thread by: Larrydoodoo, May 23, 2018, 27 replies, in forum: Troubleshooting
Showing results 1 to 18 of 18
Search Again