1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Dcbarry
    Post

    Marlin 2.0.X Autolevel

    Nol, what customizations have you made to your r1 +? Did you just make changes too config.h, and if so, would you mind posting?
    Post by: Dcbarry, May 15, 2020 in forum: Mods and Upgrades
  2. Dcbarry
    Post

    Solved Loading filament - problems.

    Mark, I’m on all stock original r1+ but hate feeding the damn thing. Are you aging to insert a tube into the existing spot and stop right above...
    Post by: Dcbarry, Nov 30, 2019 in forum: Troubleshooting
  3. Dcbarry
    Post

    Solved Where to get thermosister replacement (r1+)

    Although I had some initial problems reaching them...( don’t bother with the phone line.... open a ticket.....).... despite my earlier post, they...
    Post by: Dcbarry, Jan 3, 2019 in forum: Troubleshooting
  4. Dcbarry
    Thread

    Unanswered Any mods to improve feeding filament on stock hexagon?

    Hi all. I,m looking for minor mods or suggestions to make it easier to thread in the filament. I find it tricky and double that for my son....
    Thread by: Dcbarry, Dec 19, 2018, 1 replies, in forum: General Questions
  5. Dcbarry
    Post

    Solved Where to get thermosister replacement (r1+)

    I am a knucklehead. In reality, I have had so much going on that I realized I was thinking of the size of the heating element, not the...
    Post by: Dcbarry, Dec 6, 2018 in forum: Troubleshooting
  6. Dcbarry
    Post

    Solved Where to get thermosister replacement (r1+)

    So they (Robo) worked through their problems on their sales platform and I received a package today Unfortunately it was the wrong thermosister....
    Post by: Dcbarry, Dec 3, 2018 in forum: Troubleshooting
  7. Dcbarry
    Thread

    Solved Where to get thermosister replacement (r1+)

    I keep wiggling those tiny leads apart, but they find their way back to shorting each other out internal to the cylindrical portion.where I cant...
    Thread by: Dcbarry, Nov 28, 2018, 18 replies, in forum: Troubleshooting
  8. Dcbarry
    Thread

    Aliexpress Hexagon Hot Ends?

    Would appreciate commentary/thoughts/insight on using the below as direct replacement for the "stock" hexagon hot end. As noted in other...
    Thread by: Dcbarry, Jun 15, 2018, 2 replies, in forum: General Questions
  9. Dcbarry
    Post

    Solved Print failure analysis anyone?

    Meant to close out thread earlier, Cleared up major problems after completely resetting the matter control settings. No longer getting prints...
    Post by: Dcbarry, Jun 12, 2018 in forum: Troubleshooting
  10. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Im confused too... Waldo are you saying this is an R1+ piece? I'm not seeing it on the R1+ in front of me, which is supposedly stock. from...
    Post by: Dcbarry, Jun 10, 2018 in forum: General Questions
  11. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    The brass colored piece is in a post by where's waldo about 6 posts up the chain.... sorry not sure how to do a link back, I'll quote it below.
    Post by: Dcbarry, Jun 10, 2018 in forum: General Questions
  12. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    It appears to be revised version of the piece the z limit switches attach to (left and right). It appears to be a molded piece, not printed. The...
    Post by: Dcbarry, Jun 10, 2018 in forum: General Questions
  13. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Update..... I'm actively printing pieces. This is a great community. two questions for today... 1) I can't identify this piece in Mike Ks...
    Post by: Dcbarry, Jun 10, 2018 in forum: General Questions
  14. Dcbarry
    Thread

    Solved Print failure analysis anyone?

    Would appreciate ideas on what went wrong here. After finally having a few relative successes with smaller parts of the R1 from Mike Kelley's...
    Thread by: Dcbarry, Jun 7, 2018, 2 replies, in forum: Troubleshooting
  15. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    HI, just wanted to provide an update.... I got a quote for roughly $190 for 'nearly' all the parts from ROBO direct. Ouch. $60 of that is the...
    Post by: Dcbarry, Jun 7, 2018 in forum: General Questions
  16. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Been distracted with another issue, ;-(, but still working through all this.... thanks to all for the advice to date!
    Post by: Dcbarry, Jun 1, 2018 in forum: General Questions
  17. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Do the exreuder and x axis use the same stepper on the stock unit? I noticed underneath that the y axis has a different notation from the z axis...
    Post by: Dcbarry, May 30, 2018 in forum: General Questions
  18. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    As I understand, the R1+ (which I have) is a lead screw device. Would a better picture clarify? The bed does say R1 Plus. I myself wouldn’t...
    Post by: Dcbarry, May 30, 2018 in forum: General Questions
  19. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Good news! After a bit of a scare thinking either the power supply or the controller was blown, turns out someone decided to rewire the AC...
    Post by: Dcbarry, May 30, 2018 in forum: General Questions
  20. Dcbarry
    Post

    Need *everything* for the Z axis and extruder

    Geof and Mark: Thank you for jumping in! Hope the photo is clear enough. Sorry for the busy background, took this picture yesterday. As you...
    Post by: Dcbarry, May 29, 2018 in forum: General Questions
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2