1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Brian Guenther
    Post

    Miniature Printing and Magic Layer Height

    Thanks for the quick reply! So I’m looking at more 28mm height minis. Tabletop gaming and painting type stuff. The magic layer height is just...
    Post by: Brian Guenther, Oct 25, 2018 in forum: General Questions
  2. Brian Guenther
    Thread

    Miniature Printing and Magic Layer Height

    So, I've been doing a lot of testing and prinitng on my C2 over the last couple months and have been learning how to solve problems myself and...
    Thread by: Brian Guenther, Oct 25, 2018, 7 replies, in forum: General Questions
  3. Brian Guenther
    Post

    Solved Might be an issue with Cura, but there's a pattern

    Hey, sorry for the delay, my job has intense hours and I finally have gotten a chance to get back here. Thank you for explaining the z-offset to...
    Post by: Brian Guenther, Jun 24, 2018 in forum: Troubleshooting
  4. Brian Guenther
    Post

    Solved Might be an issue with Cura, but there's a pattern

    Okay so I did it with paper and ran through the regular routine and it printed nicely. I guess I’m confused why I have to run the spiral bed level...
    Post by: Brian Guenther, Jun 20, 2018 in forum: Troubleshooting
  5. Brian Guenther
    Post

    Solved Might be an issue with Cura, but there's a pattern

    Hey there, I use the small card that came with the printer.
    Post by: Brian Guenther, Jun 19, 2018 in forum: Troubleshooting
  6. Brian Guenther
    Thread

    Solved Might be an issue with Cura, but there's a pattern

    So, just recently I received some help with a bed leveling issue from you guys, so I thought I would run something else by you now. Full...
    Thread by: Brian Guenther, Jun 19, 2018, 8 replies, in forum: Troubleshooting
  7. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    So after meticulously adding tape pieces to the pegs for a couple hours. The printer is printing acceptably now. I am going to watch it for a...
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  8. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    Thanks so much. Let me get to work trying to get it level. I'll report back if I have any issues or its resolved. Thanks again!
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  9. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    So, forgive me, but what is a shim?
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  10. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    I'm not sure which underside(I don't know which one has the magnets) you wanted so I took pictures of both:[ATTACH] [ATTACH]
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  11. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    So I did everything you said and ran a "bed level test" print job that came on the printer. The result is this:[ATTACH] Thank you for your...
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  12. Brian Guenther
    Post

    Solved Robo C2 print bed leveling issue

    Oh shoot, I am in the wrong troubleshooting area. I'm sorry, could this be moved to the C2 troubleshooting page?
    Post by: Brian Guenther, Jun 18, 2018 in forum: Troubleshooting
  13. Brian Guenther
    Thread

    Solved Robo C2 print bed leveling issue

    So I am very new to 3D printing and the Robo C2 is my first printer. I used the printer for about 3 days without major issue. Then I had my first...
    Thread by: Brian Guenther, Jun 18, 2018, 18 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again