1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. aenea22980
    Post

    Unanswered Print head pressing on Bed for first layer

    How weird. Mine did that for a while and I ran it through the manual level calibration cycle again and it seemed to fix it.
    Post by: aenea22980, Apr 15, 2016 in forum: Troubleshooting
  2. aenea22980
    Post

    Unresolved Filament keeps breaking???

    Some suggestions: it does look like the temp might be too high and the heat is traveling up the hot end and softening the filament before it can...
    Post by: aenea22980, Apr 14, 2016 in forum: Troubleshooting
  3. aenea22980
    Post

    Unresolved X-Axis bouncing?

    When I got my printer it did something similar, the screw that was supposed to hit the switch wasn't long enough to depress the metal bar enough...
    Post by: aenea22980, Apr 14, 2016 in forum: Troubleshooting
  4. aenea22980
    Post

    Solved Something crazy just happened with my Robo 3D Plus

    I don't know if you're already returning it or not, but my thought on your original post - I run into the issue where the printer cannot be found...
    Post by: aenea22980, Apr 14, 2016 in forum: Troubleshooting
  5. aenea22980
    Post

    Unanswered Lost Magnet - Replacement?

    Robo can send them to you, they're like 50c each so I'd suggest get a couple for insurance. If you call their help line just get to the parts...
    Post by: aenea22980, Apr 14, 2016 in forum: Troubleshooting
  6. aenea22980
    Post

    PLA Microcenter Inland PLA

    Hah! That's awesome! I never really thought about that, so you leave just the bottom open so the bed can slide in and out? My current project...
    Post by: aenea22980, Apr 5, 2016 in forum: Printing Filament
  7. aenea22980
    Post

    PLA Microcenter Inland PLA

    That's an extremely neat print. I think part of my problem with ABS is that the printer is on our computer desk, right next to the great room,...
    Post by: aenea22980, Apr 5, 2016 in forum: Printing Filament
  8. aenea22980
    Post

    ABS 20lb spool?!

    Have no idea if this is good filament or not, but it's the equivalent of paying $28 a kg at that price, which seems expensive when you can get...
    Post by: aenea22980, Apr 5, 2016 in forum: Printing Filament
  9. aenea22980
    Post

    PLA Microcenter Inland PLA

    I'm using the Inland silver PLA, 200 degrees, bed at 60, gluesticked. Seems to work fine. My problem was for so long I only used ABS, so...
    Post by: aenea22980, Apr 5, 2016 in forum: Printing Filament
  10. aenea22980
    Post

    MatterControl issue

    I've heard that's a great program, but not everyone can afford $150 for software for 3D printing. After buying the printer I certainly didn't...
    Post by: aenea22980, Apr 5, 2016 in forum: General Questions
  11. aenea22980
    Post

    Solved Would the new Z Axis motors and rods need a firmware update?

    Ah, I had no idea what lead screw meant, I've always called it just the z axis. I see the firmware update on Robo's page. Thanks. (For future...
    Post by: aenea22980, Apr 4, 2016 in forum: General Questions
  12. aenea22980
    Post

    MatterControl issue

    I found in MatterControl that there were a lot of settings that aren't accessible from the UI, you have to go to the little x-shaped tool symbol...
    Post by: aenea22980, Apr 4, 2016 in forum: General Questions
  13. aenea22980
    Post

    Unanswered Quieter fans for the R1

    My hot end fan and the bed fan were making a horrible noise when running together, so I ended up taking the hot end fan off and removing the...
    Post by: aenea22980, Apr 3, 2016 in forum: General Questions
  14. aenea22980
    Post

    Stepper Motors & Spare Parts

    Robo 3d sells the motor here for $14. Have no idea if that's a good price or not but at least you can be sure it should work and fit your...
    Post by: aenea22980, Apr 3, 2016 in forum: General Questions
  15. aenea22980
    Thread

    Solved Would the new Z Axis motors and rods need a firmware update?

    I have an older Robo, regular R1, but I'd like to get the new Z Axis motors and rods that they have for sale here since they do away with the...
    Thread by: aenea22980, Apr 3, 2016, 2 replies, in forum: General Questions
  16. aenea22980
    Post

    Solved Print bed fan won't turn on

    Just an update - I checked everything for the fan to make sure the fan itself wasn't burned out (it wasn't) or that the power cables to the fan...
    Post by: aenea22980, Apr 3, 2016 in forum: Troubleshooting
  17. aenea22980
    Thread

    Solved Print bed fan won't turn on

    When I first got my printer I was using ABS, so I unplugged the power to the fan that blows on the print bed. For whatever reason even when I...
    Thread by: aenea22980, Mar 27, 2016, 2 replies, in forum: Troubleshooting
  18. aenea22980
    Post

    Partially Solved feeder chews filament

    I had a lot of trouble with my filament stripping on the hobbed bolt, I tried cleaning out the print head, increasing the tension, changing...
    Post by: aenea22980, Mar 27, 2016 in forum: Troubleshooting
Showing results 1 to 18 of 18
Search Again