1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Springpatch Newb
    Post

    Answered Missing layers from print and heater problems

    Silly question.... I only know that it is a robo r1 + 3d printer, where would I find that information on the printer? Sent from my SM-N960U using...
    Post by: Springpatch Newb, Jul 21, 2019 in forum: Troubleshooting
  2. Springpatch Newb
    Post

    Answered Missing layers from print and heater problems

    P.S. if possible would like to know your suggestions for a new 3d printer as long as it is under $400 as a replacement for I am wanting to buy a...
    Post by: Springpatch Newb, Jul 21, 2019 in forum: Troubleshooting
  3. Springpatch Newb
    Thread

    Answered Missing layers from print and heater problems

    My robo 3d r1 plus has been having problems where it doesn't print some layers because it either for some reason gets too hot or the temp drops...
    Thread by: Springpatch Newb, Jul 21, 2019, 6 replies, in forum: Troubleshooting
  4. Springpatch Newb
    Post

    Unresolved Printing With Supports Help Request

    P.S. I am using Materrcontrol as my 3d printing software. It only has grid and lines as outside support options. Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 18, 2019 in forum: Troubleshooting
  5. Springpatch Newb
    Thread

    Unresolved Printing With Supports Help Request

    I have tried printing a few items but I can't quite figure out the process for Inputing the settings to make the supports easy to remove. I have...
    Thread by: Springpatch Newb, May 18, 2019, 4 replies, in forum: Troubleshooting
  6. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    Just as a thought, if it's a lost cause what would you recommend for a good replacement printer that isn't too expensive? Sent from my SM-N960U...
    Post by: Springpatch Newb, May 14, 2019 in forum: Troubleshooting
  7. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    E3D All-metal v6 HotEnd Full Kit... https://www.amazon.com/dp/B00NAK9JFO?ref=ppx_pop_mob_ap_share Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 14, 2019 in forum: Troubleshooting
  8. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    I will post some pictures later on today Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 12, 2019 in forum: Troubleshooting
  9. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    The original hot end was a hexagonal shaped unit and the one that I got was a round unit that is wider than the original. Sent from my SM-N960U...
    Post by: Springpatch Newb, May 12, 2019 in forum: Troubleshooting
  10. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    It was more expensive than the standard e3d v6 hot end Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 12, 2019 in forum: Troubleshooting
  11. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    The hot end is wider than the mount which held the original got end that was installed Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 11, 2019 in forum: Troubleshooting
  12. Springpatch Newb
    Post

    Unanswered Wrong hot end e3d v6

    It is a wider hot end and it is longer (slightly) but that is all that I know Sent from my SM-N960U using Tapatalk
    Post by: Springpatch Newb, May 11, 2019 in forum: Troubleshooting
  13. Springpatch Newb
    Thread

    Unanswered Wrong hot end e3d v6

    To anyone out there I had a problem with the filament getting stuck in the hot end of my robo r1 + 3d printer and so I bought a new one online...
    Thread by: Springpatch Newb, May 11, 2019, 14 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again