1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Alvin Jacob
    Thread

    Is the robo R2 Hot end same as that of R1

    Hi, I wanted to buy a spare hotend just in case, is the hotend for R2 same as that of R1. Alvin Jacob
    Thread by: Alvin Jacob, Dec 5, 2019, 2 replies, in forum: General Questions
  2. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    I set the Z offset to -6.85. It was saved in the EEPROM. Checked in the printer and the code. BUT when I give the command for Fine tune offset...
    Post by: Alvin Jacob, Oct 24, 2019 in forum: Troubleshooting
  3. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    I went through the bed leveling procedure at the beginning of the this Troubleshooting area....
    Post by: Alvin Jacob, Oct 23, 2019 in forum: Troubleshooting
  4. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    Too scared actually. Anyways I will try the above steps today. Many Thanks!
    Post by: Alvin Jacob, Oct 22, 2019 in forum: Troubleshooting
  5. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    Do the mentioned steps applicable for R2?
    Post by: Alvin Jacob, Oct 20, 2019 in forum: Troubleshooting
  6. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    Still Listening!!
    Post by: Alvin Jacob, Oct 19, 2019 in forum: Troubleshooting
  7. Alvin Jacob
    Post

    Printer bed and Extruder crashing

    Many thanks for the responses, Unfortunately, I had to stop working on the R2 printer presuming the crash. @tkoco "Just a point of interest, I...
    Post by: Alvin Jacob, Oct 19, 2019 in forum: Troubleshooting
  8. Alvin Jacob
    Thread

    Printer bed and Extruder crashing

    Hi, The issue started today, on giving the command for fine-tune settings from the LCD screen, the auto-leveling is done. But then the bed goes...
    Thread by: Alvin Jacob, Oct 2, 2019, 23 replies, in forum: Troubleshooting
  9. Alvin Jacob
    Post

    Bed not heating

    No, it just switches itself off. A diode got burnt which was for the bed. I had to unplug each wire and try to find out the origination of the...
    Post by: Alvin Jacob, Sep 16, 2019 in forum: Troubleshooting
  10. Alvin Jacob
    Post

    Bed not heating

    I had resolved the problem. Some malfunctioning in the PCB board. Had to replace it. No errors were shown since the whole system restarts. But...
    Post by: Alvin Jacob, Sep 16, 2019 in forum: Troubleshooting
  11. Alvin Jacob
    Thread

    Bed not heating

    Hi, On giving the command to increase the temperature of the bed, the whole system restarts itself. Please help!!
    Thread by: Alvin Jacob, Sep 14, 2019, 9 replies, in forum: Troubleshooting
  12. Alvin Jacob
    Post

    Robo 3D R2 Does not start

    Yes. Over removing the bottom cover, found that the fuse is blown. Will replace it with a new one. I believe that will solve the problem. Hoping...
    Post by: Alvin Jacob, Sep 12, 2019 in forum: Troubleshooting
  13. Alvin Jacob
    Thread

    Robo 3D R2 Does not start

    Hi, My R2 printer is not starting when I switch it on from the back button. By not starting I mean, no display, the fans don't turn on as they...
    Thread by: Alvin Jacob, Sep 12, 2019, 4 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again