1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Henradrie
    Post

    Solved Inconsistent extrusion R1

    That was too much work compared to doubling up the elastic. Problem solved, at least until the elastic gives out. Not a fix I would recommend, but...
    Post by: Henradrie, Feb 2, 2021 in forum: Troubleshooting
  2. Henradrie
    Post

    Solved Inconsistent extrusion R1

    The printer came with 1 screw so I removed it and put the bands on. It also came with parts in a bag. Maybe I'll have something in my stock of...
    Post by: Henradrie, Feb 1, 2021 in forum: Troubleshooting
  3. Henradrie
    Post

    Solved Inconsistent extrusion R1

    Here are the pictures. [IMG][IMG][IMG] Tube is 2cm long. Sent from my SM-A705W using Tapatalk
    Post by: Henradrie, Jan 31, 2021 in forum: Troubleshooting
  4. Henradrie
    Post

    Solved Inconsistent extrusion R1

    I'm out of town at the moment but will get pictures when I can. In the meantime here is some more information that might be helpful. Consider this...
    Post by: Henradrie, Jan 31, 2021 in forum: Troubleshooting
  5. Henradrie
    Thread

    Solved Inconsistent extrusion R1

    I've been working on getting an R1 working. The latest problem I can't solve is inconsistent extrusion. My parts come out looking this. The...
    Thread by: Henradrie, Jan 30, 2021, 8 replies, in forum: Troubleshooting
  6. Henradrie
    Thread

    Unanswered Could custom shaft aligner contribute to z-banding?

    I have an original R1 and it has z banding issues. Through this forum I've discovered that this is a common problem and am going to be replacing...
    Thread by: Henradrie, Jan 16, 2021, 2 replies, in forum: Troubleshooting
  7. Henradrie
    Post

    Answered Ive got a major z axis problem

    I used this code instead. G28 ; G29 ; G92 E0 ; G01 Z0.10 ; Adjust this to deal with first layer nozzle height G92 Z0 ;
    Post by: Henradrie, Jan 15, 2021 in forum: Troubleshooting
  8. Henradrie
    Post

    Unresolved Potential heat break issues

    Thanks for the suggestions. I started reading into nozzle seasoning and saw how divisive it is. Got cold feet. One article I read mentioned that...
    Post by: Henradrie, Oct 4, 2020 in forum: Troubleshooting
  9. Henradrie
    Post

    Solved Z axis improperly homing

    I had something similar happen to my R1. Issue was that the vertical rods were not straight and this caused one of the limit switches to be open...
    Post by: Henradrie, Sep 23, 2020 in forum: Troubleshooting
  10. Henradrie
    Thread

    Unresolved Potential heat break issues

    I've been printing on my R1+ for a while then the quality degraded. As seen in the picture the first couple layers go down nicely then the next...
    Thread by: Henradrie, Sep 23, 2020, 4 replies, in forum: Troubleshooting
  11. Henradrie
    Post

    Unanswered X axis only moving in one direction

    Just tried that, no change. Even tried that with the extruder chip and nothing changed. I swapped the X and Y axis driver chips and swapped the...
    Post by: Henradrie, Jun 3, 2020 in forum: Troubleshooting
  12. Henradrie
    Thread

    Unanswered X axis only moving in one direction

    I have a Robo R1 beta (5/16 leadscrews) that can only move the X-axis one direction. It was working fine then just started exhibiting that...
    Thread by: Henradrie, Jun 2, 2020, 3 replies, in forum: Troubleshooting
  13. Henradrie
    Post

    Unanswered PETG clear, brown (burned?) spots

    I've never had PETG stick the nozzle to the print but I have seen the nozzle push against a clump too large to remove which messes with the...
    Post by: Henradrie, Jun 2, 2020 in forum: Troubleshooting
  14. Henradrie
    Post

    Solved Supports breaking during print

    I had some success messing with tower settings in cura. Mostly making the base of towers wider. This made the supports wider and less likely to...
    Post by: Henradrie, May 13, 2020 in forum: Troubleshooting
  15. Henradrie
    Post

    Solved Hotend wires came off

    I had success replacing the thermistor on my r1+ by connecting another thermistor up and manually pressing it against the heater block so it...
    Post by: Henradrie, May 13, 2020 in forum: Troubleshooting
  16. Henradrie
    Post

    Unanswered Help with repair

    I went to my local 3d print store for stepper drivers. Sent from my SM-G960W using Tapatalk
    Post by: Henradrie, May 1, 2020 in forum: Troubleshooting
  17. Henradrie
    Post

    Unresolved MatterControl Unable to Connect to Robo R1+

    How does it work with Cura or Pronterface? Sent from my SM-G960W using Tapatalk
    Post by: Henradrie, Apr 15, 2020 in forum: Troubleshooting
  18. Henradrie
    Post

    Small gaps while printing petg

    I tried a brand new roll with a different print and it seemed to work better. The problem seems to happen around areas with a change in direction....
    Post by: Henradrie, Mar 23, 2020 in forum: Printing Filament
  19. Henradrie
    Post

    Unanswered R1+ not printing support structures..

    Did you turn on supports? That's strange, I use mattercontrol and it always works for me. Sent from my SM-G960W using Tapatalk
    Post by: Henradrie, Mar 16, 2020 in forum: Troubleshooting
  20. Henradrie
    Post

    Unresolved Robo R1 beta with stringy prints

    Also try increasing the Z-lift. This lifts your nozzle above the print leaving some filament behind. Don't be tempted to increase your retraction...
    Post by: Henradrie, Mar 8, 2020 in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2