1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Shea Clayton
    Post

    It started with a communication issue...

    well hello! So I was able to use a standard micro USB and an iPhone brick to run the R-pi .No power issues come up on the secondary monitor. I...
    Post by: Shea Clayton, Apr 13, 2020 in forum: Troubleshooting
  2. Shea Clayton
    Post

    It started with a communication issue...

    Hey Guys, Ok, i am a little out of my depth but got an octopi image installed and it prints! It will be a learning curve but really happy i got...
    Post by: Shea Clayton, Apr 3, 2020 in forum: Troubleshooting
  3. Shea Clayton
    Post

    It started with a communication issue...

    I haven't tried Octoprint, but I will look into that now. However, I have exchanged the ribbon (old and new) pi (old and new) and screen (old and...
    Post by: Shea Clayton, Mar 31, 2020 in forum: Troubleshooting
  4. Shea Clayton
    Post

    It started with a communication issue...

    Hye Guys, So I was able to find another r-pi 3 stealing it from a Pi-Top I had, and just to eliminate that potential issue i made the swap but...
    Post by: Shea Clayton, Mar 31, 2020 in forum: Troubleshooting
  5. Shea Clayton
    Post

    It started with a communication issue...

    ok, this is getting super nuts. I replaced the ribbon to the old screen, and it boots, the screen comes up. I was then able to touch the Utility...
    Post by: Shea Clayton, Mar 30, 2020 in forum: Troubleshooting
  6. Shea Clayton
    Post

    It started with a communication issue...

    It's the purchased new one, but I can try the old (I think I did with the same results). @mark the image is the same you linked to me earlier and...
    Post by: Shea Clayton, Mar 30, 2020 in forum: Troubleshooting
  7. Shea Clayton
    Post

    It started with a communication issue...

    here is a link to the screen https://www.partsbuilt.com/c2-lcd-screen-non-hdmi/ and yes, 1000%. It was the one time i didn't.
    Post by: Shea Clayton, Mar 30, 2020 in forum: Troubleshooting
  8. Shea Clayton
    Post

    It started with a communication issue...

    unfortunately, the new screen is not the HDMI version and doesn't have the connection option.
    Post by: Shea Clayton, Mar 30, 2020 in forum: Troubleshooting
  9. Shea Clayton
    Post

    It started with a communication issue...

    here is the second image of the older screen with correct colors and right orientation
    Post by: Shea Clayton, Mar 27, 2020 in forum: Troubleshooting
  10. Shea Clayton
    Post

    It started with a communication issue...

    yep, nothing is touching. I placed the screen into the frame so insure it was isolated. No plastic/film on the screen. Weirdly the old screen...
    Post by: Shea Clayton, Mar 27, 2020 in forum: Troubleshooting
  11. Shea Clayton
    Post

    It started with a communication issue...

    So progress!, (sort of) I used the image you pointed me to Mark and the screen does show the UI but the touch screen doesn't allow selections....
    Post by: Shea Clayton, Mar 27, 2020 in forum: Troubleshooting
  12. Shea Clayton
    Post

    It started with a communication issue...

    That's correct. The HDMI port is unused (I used it only to test) and the connection from the Rpi to the display is through the ribbon cable.
    Post by: Shea Clayton, Mar 27, 2020 in forum: Troubleshooting
  13. Shea Clayton
    Post

    It started with a communication issue...

    So essentially not required? Ok, so now I am back to the screen not showing UI. Unlike the one that I replaced (it was showing a white screen)...
    Post by: Shea Clayton, Mar 27, 2020 in forum: Troubleshooting
  14. Shea Clayton
    Post

    It started with a communication issue...

    Thanks Mark!
    Post by: Shea Clayton, Mar 26, 2020 in forum: Troubleshooting
  15. Shea Clayton
    Post

    It started with a communication issue...

    Hey Mark, Yue image attached. It's the cable I am holding in my hand - to the black fitting it had been connected to in the ribbon. it's 2 leads...
    Post by: Shea Clayton, Mar 26, 2020 in forum: Troubleshooting
  16. Shea Clayton
    Post

    It started with a communication issue...

    SO I go in the new LCD screen and new RPi ribbon cable (I have the older C2). I went to install the cable and notice the smaller cable that run at...
    Post by: Shea Clayton, Mar 26, 2020 in forum: Troubleshooting
  17. Shea Clayton
    Post

    It started with a communication issue...

    That is interesting. I did for a hot second use generic power supply that just fit (I know horrible idea). Perhaps that created the first issue,...
    Post by: Shea Clayton, Mar 20, 2020 in forum: Troubleshooting
  18. Shea Clayton
    Post

    It started with a communication issue...

    Yes, mine is the older ribbon cable. I was able to plugin and HDMI cable to an exterior monitor and was able to see the screen UI. If the screen...
    Post by: Shea Clayton, Mar 20, 2020 in forum: Troubleshooting
  19. Shea Clayton
    Thread

    It started with a communication issue...

    Hey guys need some help. I had been going back and forth with support but they went silent. Here is my post to support: Me: I recently moved...
    Thread by: Shea Clayton, Mar 20, 2020, 53 replies, in forum: Troubleshooting
Showing results 1 to 19 of 19
Search Again