1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. chn9292
    Thread

    marlin timeout error

    when ı upload marlin to roboboard , ı got info from arduino programme as like avrdude: stk500v2_ReceiveMessage(): timeout avrdude:...
    Thread by: chn9292, Jan 22, 2021, 1 replies, in forum: Troubleshooting
  2. chn9292
    Post

    thermistor Issue

    in generally i can not get value when ı flip probes.
    Post by: chn9292, Dec 21, 2020 in forum: Troubleshooting
  3. chn9292
    Post

    thermistor Issue

    I have measured 1 to 5 and 13 to 15 pins. ı got 3,8k 1 to 5 and when i flip there is no value. 13 to 15 is 4,7k and there is no valuse at flip....
    Post by: chn9292, Dec 21, 2020 in forum: Troubleshooting
  4. chn9292
    Post

    thermistor Issue

    I've already replaced it new one. could it be on ribbon from mainboard?
    Post by: chn9292, Dec 21, 2020 in forum: Troubleshooting
  5. chn9292
    Thread

    thermistor Issue

    thermıstor shows 190 C degrees in room tempature. what kind of problem could be in there ? because of this ı can not make PID. Heater warm it...
    Thread by: chn9292, Dec 21, 2020, 7 replies, in forum: Troubleshooting
  6. chn9292
    Post

    touch screen doesnt work ( always black)

    ı connected putty. I replaced driver of LCD screen. and now there is always pnk screen which has text robo. Freeze type has changed :) :(
    Post by: chn9292, May 13, 2020 in forum: Troubleshooting
  7. chn9292
    Post

    touch screen doesnt work ( always black)

    also i never reach to raspberry via putty.
    Post by: chn9292, May 13, 2020 in forum: Troubleshooting
  8. chn9292
    Post

    touch screen doesnt work ( always black)

    there is something wrong or i couldnt , i dont know , i got image belon LCD 5'' and i need to boot via octoprint. also without image file there is...
    Post by: chn9292, May 13, 2020 in forum: Troubleshooting
  9. chn9292
    Post

    touch screen doesnt work ( always black)

    it seems like from octoprint easier than putty. may i directly connect SD via USB port and may i load from usb folder as like upload gcode file ?
    Post by: chn9292, May 9, 2020 in forum: Troubleshooting
  10. chn9292
    Post

    touch screen doesnt work ( always black)

    i set image file up to SD. do you Show me link belong steps of boot to rasberry ?
    Post by: chn9292, May 9, 2020 in forum: Troubleshooting
  11. chn9292
    Post

    touch screen doesnt work ( always black)

    İ was going to do but screen went back however ı cant touch it. it doesnt responsive. now screen is open but , there is no behavior. Freeze...
    Post by: chn9292, May 9, 2020 in forum: Troubleshooting
  12. chn9292
    Thread

    touch screen doesnt work ( always black)

    İ removed ribbon cable of touchscreen and connected again correct , but touchscreen doesnt give answer , it always black also when I connect...
    Thread by: chn9292, May 9, 2020, 12 replies, in forum: Troubleshooting
  13. chn9292
    Post

    wi-fi connection doesnt work.

    Yes every device connect to wifi well without Robo. :( anyway , i connected via cat6 cable. I use 2.4 GHZ value on wifi connection also tired...
    Post by: chn9292, Apr 27, 2020 in forum: Troubleshooting
  14. chn9292
    Post

    wi-fi connection doesnt work.

    everthing was normal. ı shutted it down and open again machine , it couldnt reach wifi. only saying ''connecting..'' due to , ı dont see any ıp...
    Post by: chn9292, Apr 18, 2020 in forum: Troubleshooting
  15. chn9292
    Post

    wi-fi connection doesnt work.

    no , everthing is normal actually , ı connect via Ethernet and searching over octo print but negative :(
    Post by: chn9292, Apr 18, 2020 in forum: Troubleshooting
  16. chn9292
    Thread

    wi-fi connection doesnt work.

    ı select to wifi configure to connect wifi but it doesnt Show networks. just stay as connecting.. need help !
    Thread by: chn9292, Apr 17, 2020, 9 replies, in forum: Troubleshooting
  17. chn9292
    Post

    bed crashes to nozzle always up after using z-offset wizard

    Thank you so much , i solved problem.
    Post by: chn9292, Apr 17, 2020 in forum: Troubleshooting
  18. chn9292
    Post

    bed crashes to nozzle always up after using z-offset wizard

    how can ı get lastest verison of it to upload via usb disk ? ı solved problem but now , there is no connection with wifi. it doesnt find any...
    Post by: chn9292, Apr 17, 2020 in forum: Troubleshooting
  19. chn9292
    Post

    bed crashes to nozzle always up after using z-offset wizard

    2,0,0-r2,6 and marlin is 1,1,6_roboversion_1,2,4_R2.hex
    Post by: chn9292, Apr 14, 2020 in forum: Troubleshooting
  20. chn9292
    Post

    bed crashes to nozzle always up after using z-offset wizard

    as ı remember , last version cause machine did not up to date itself. problem is bed always wants to up. when I click to raise , it goes down and...
    Post by: chn9292, Apr 12, 2020 in forum: Troubleshooting
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2