1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Ok, printer is working again! Robo recommended swapping the Z-motor connections on the board which got the motors moving but skipping steps. So,...
    Post by: JetMang, Mar 21, 2017 in forum: Troubleshooting
  2. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Thanks for the help, I greatly appreciate it! I'll report back the results. Unfortunately I won't be able to work on the printer again until after...
    Post by: JetMang, Mar 16, 2017 in forum: Troubleshooting
  3. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Ok, that would make sense as the motors act as though they don't have enough power/torque to turn. I will give that a shot. I'm pretty sure I have...
    Post by: JetMang, Mar 16, 2017 in forum: Troubleshooting
  4. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    I tried the firmware for both the r1 and r1+ And neither worked right in the z axis
    Post by: JetMang, Mar 16, 2017 in forum: Troubleshooting
  5. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Whoops, sorry, I meant the firmware. I did swap around the stepper drivers too plus the computer drivers. All with the same result and the z-axis...
    Post by: JetMang, Mar 16, 2017 in forum: Troubleshooting
  6. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Ok guys, well the new board got the machine talking again and everything works except the Z-axis. It tries to move the Z, but just makes a whine...
    Post by: JetMang, Mar 15, 2017 in forum: Troubleshooting
  7. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Well, got a call from Robo today, but not a ton of help. They recommended updating the firmware which I did and it's still doing the same thing....
    Post by: JetMang, Mar 13, 2017 in forum: Troubleshooting
  8. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    I'll take a look at the thread. I've also emailed Robo so will hopefully hear back from them tomorrow. Thanks!
    Post by: JetMang, Mar 12, 2017 in forum: Troubleshooting
  9. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Yeah, I did that and still the same thing. :( I reinstalled drivers and such too and no luck. The printer and computer aren't communicating for...
    Post by: JetMang, Mar 12, 2017 in forum: Troubleshooting
  10. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    I'm wondering if the control board is hosed. And of course just my luck, Robo is out of stock on those...
    Post by: JetMang, Mar 12, 2017 in forum: Troubleshooting
  11. JetMang
    Post

    Solved R1+ Printer not connecting and showing gibberish

    Well, a new cable didn't do it. Same problem. :(
    Post by: JetMang, Mar 12, 2017 in forum: Troubleshooting
  12. JetMang
    Thread

    Solved R1+ Printer not connecting and showing gibberish

    Hey guys, All of a sudden my R1+ printer stopped connecting to my computer. I've tried connecting to a separate computer that I've printed from...
    Thread by: JetMang, Mar 12, 2017, 20 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again