1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. J_Man
    Post

    Solved M999 error

    I want to revive this post to add to it. I resent started getting the M999 running print from Matter Control. I couldn't actually continue. It was...
    Post by: J_Man, Sep 4, 2017 in forum: Troubleshooting
  2. J_Man
    Post

    Solved Unlevel bed....

    I thought I knew, but I'm failing to find it. How do you turn off auto leveling?
    Post by: J_Man, Aug 7, 2017 in forum: Troubleshooting
  3. J_Man
    Post

    Solved Unlevel bed....

    My Wanhao Duplicator 4S has the 4 point manual bed leveling, and that works fine. I figured if there was a way to bring that to the C2, it work...
    Post by: J_Man, Aug 7, 2017 in forum: Troubleshooting
  4. J_Man
    Post

    Solved uneven bed plate, is it fixable

    If I can get the auto level to turn off and stop throwing it off, I think it'll print great constantly. I'd like a single bolt and a bow tie thumb...
    Post by: J_Man, Aug 7, 2017 in forum: Troubleshooting
  5. J_Man
    Post

    Solved Unlevel bed....

    Mine keeps moving. I had it level and it ran ok for a few prints, then was high in the back. Adjusting the bolts worked to get it through the...
    Post by: J_Man, Aug 7, 2017 in forum: Troubleshooting
  6. J_Man
    Post

    Solved Unlevel bed....

    Finished another print and had the same high in the back starting another print. I'll try the fine tuning wizard tonight and see what that does...
    Post by: J_Man, Aug 7, 2017 in forum: Troubleshooting
  7. J_Man
    Post

    Solved Unlevel bed....

    New issue I just discovered while setting up a print right after the last. When it laser leveled, it was off on the back again when it started...
    Post by: J_Man, Aug 6, 2017 in forum: Troubleshooting
  8. J_Man
    Post

    Solved uneven bed plate, is it fixable

    I posted in another thread, but basically I got rid of the screws and caps they had. I replaced it with screws and bolts. I have it manually leel...
    Post by: J_Man, Aug 6, 2017 in forum: Troubleshooting
  9. J_Man
    Post

    Solved Unlevel bed....

    I finally solved my bed level issues. I had bent the metal when I first got it to get it level. It was warped horribly. Still, I could never get...
    Post by: J_Man, Aug 6, 2017 in forum: Troubleshooting
  10. J_Man
    Post

    Issues with overhang/underside of prints.

    I actually had this issue when I upgraded Cura to 2.5. Overhangs were horrible, rafts overly stuck to the prints, and under prints looked...
    Post by: J_Man, Aug 6, 2017 in forum: Troubleshooting
  11. J_Man
    Post

    Simplify 3D and Robo C2

    Yeah I have the z offset fine when it's setup in Cura. I was testing a print now that's been going over an hour and so far no shifts and I have...
    Post by: J_Man, Jun 29, 2017 in forum: Troubleshooting
  12. J_Man
    Post

    Simplify 3D and Robo C2

    Ok, thanks. I'll give that a try. I had saved a file to a USB drive and tried loading it up. The Z coordinates were off. It ended up being too...
    Post by: J_Man, Jun 29, 2017 in forum: Troubleshooting
  13. J_Man
    Post

    Simplify 3D and Robo C2

    I sent an email to the help address. I figure maybe they might can give me some info. I've been Google searching for days and haven't found...
    Post by: J_Man, Jun 29, 2017 in forum: Troubleshooting
  14. J_Man
    Post

    Simplify 3D and Robo C2

    It apparently will connect fine to the R1+, but I'm fine with Matter Control for now. I mostly use that printer for the big stuff. I think that's...
    Post by: J_Man, Jun 29, 2017 in forum: Troubleshooting
  15. J_Man
    Post

    Simplify 3D and Robo C2

    I guess I'm not sure how to do that. Is there a walk through somewhere for it?
    Post by: J_Man, Jun 29, 2017 in forum: Troubleshooting
  16. J_Man
    Thread

    Simplify 3D and Robo C2

    I finally made the purchase to get Simplify 3D. Mostly for my Duplicator 4S. I'm glad I finally did it as the 4S is quickly becoming one of my top...
    Thread by: J_Man, Jun 29, 2017, 10 replies, in forum: Troubleshooting
  17. J_Man
    Post

    Unresolved USB issue

    I finally got them on the phone. The recommendation was to schedule a tech call and probably it'll result in changing the board. I was looking at...
    Post by: J_Man, May 20, 2017 in forum: Troubleshooting
  18. J_Man
    Thread

    Unresolved USB issue

    Since getting my Robo R1+, the usb port had to be wiggled when the cable was plugged. I started getting a comm 5 was in use error when trying to...
    Thread by: J_Man, May 14, 2017, 6 replies, in forum: Troubleshooting
  19. J_Man
    Post

    Stringy Print

    Yeah it printed looking like molting plastic. More like a liquid. The previous prints were smaller and didn't really show it that much.
    Post by: J_Man, Apr 12, 2017 in forum: Troubleshooting
  20. J_Man
    Post

    Stringy Print

    This should show better. The bottom of it. Also there is some warping on the left side too. I'm sure this would be fixed by not printing a raft....
    Post by: J_Man, Apr 12, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 36 Next >
Search Again
Page 1 of 2