1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. KenO
    Post

    Test your printers clearance and tolerance by Maker's Muse

    Sorry for the late response. I did this a couple years ago when my R2 was new. I checked out Angus of Maker's Muse this morning and I see that...
    Post by: KenO, Apr 4, 2020 in forum: Show and Tell
  2. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    I have only sprayed the spool holder twice. I did not wipe it off. Note that I just started using the teflon spray for the last three or four TPU...
    Post by: KenO, Mar 27, 2020 in forum: Mods and Upgrades
  3. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    Another solution to this problem I solved by using Dry Lube with Teflon. I sprayed the inside of the spool and the spool arm on the printer and I...
    Post by: KenO, Mar 26, 2020 in forum: Mods and Upgrades
  4. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    Post by: KenO, Mar 26, 2020 in forum: Mods and Upgrades
  5. KenO
    Post

    Palette 2/Palette 2 Pro

    Tkoco, I responded to your email and said that that would be fine. Probably more easily located if it was there. Ken
    Post by: KenO, Feb 7, 2020 in forum: Projects
  6. KenO
    Post

    Palette 2/Palette 2 Pro

    Preamble on how I was able to get the Mosaic Palette 2 up and working. Note that I have tried hard to make it understandable. I am not very good...
    Post by: KenO, Jan 31, 2020 in forum: Projects
  7. KenO
    Post

    Palette 2/Palette 2 Pro

    I have the instructions almost complete. Still proof reading them. However, the following is just a check to see if a cut and paste link works:...
    Post by: KenO, Jan 31, 2020 in forum: Projects
  8. KenO
    Post

    Palette 2/Palette 2 Pro

    Give me a couple of days to put it all together. Ken
    Post by: KenO, Jan 29, 2020 in forum: Projects
  9. KenO
    Post

    Palette 2/Palette 2 Pro

    I finally got the my Palette 2S to work. I used Cura 2.5.0 that Robo provided when I purchased the R2 to access Octopi. After assuring myself that...
    Post by: KenO, Jan 28, 2020 in forum: Projects
  10. KenO
    Post

    Palette 2/Palette 2 Pro

    Alien or ?: finally got the palette to run and start a print, but how do you jog the filament when it asks you to load? That function is not...
    Post by: KenO, Jan 28, 2020 in forum: Projects
  11. KenO
    Post

    Palette 2 Pro Setup Experience

    The idea of linking two Raspberry Pi's together was not intended. It was to simply to locate a 2nd Raspberry Pi above the other, but only one of...
    Post by: KenO, Jan 18, 2020 in forum: General Questions
  12. KenO
    Post

    Palette 2 Pro Setup Experience

    OK, there is so many bits and pieces of info on how to get the Palette to work, that this is good info. I did make a duplicate SD card and saved...
    Post by: KenO, Jan 17, 2020 in forum: General Questions
  13. KenO
    Post

    Palette 2 Pro Setup Experience

    Partsbuild 3d sells a replacement Raspberry Pi for the Robo C1/C2's. Rather than re-program the existing Raspberry Pi, mount a replacement on a 3d...
    Post by: KenO, Jan 17, 2020 in forum: General Questions
  14. KenO
    Post

    PALATTE 2 USERS?

    What file format would you be starting with that you want to create the STL file from?
    Post by: KenO, Jan 13, 2020 in forum: General Questions
  15. KenO
    Post

    Palette 2/Palette 2 Pro

    I just noted that this link from Mosaic:...
    Post by: KenO, Jan 10, 2020 in forum: Projects
  16. KenO
    Post

    Palette 2/Palette 2 Pro

    Jonny Yeu form Mosaic last month gave instructions to add plugins to the OctoPi. The link is...
    Post by: KenO, Jan 10, 2020 in forum: Projects
  17. KenO
    Post

    Palette 2/Palette 2 Pro

    Question on Palette 2 setup. Jonny Yeu of Mosaic notes two plugins that I assume need to be added to the Robo R2's Raspberry Pi (OptiPi). they are...
    Post by: KenO, Jan 10, 2020 in forum: Projects
  18. KenO
    Post

    R2 reports constant, incorrect extruder temperature

    I was having a problem with the extruder sensing the correct temperature and it turned out that the allen set screw that holds the sensor in...
    Post by: KenO, Aug 22, 2019 in forum: Troubleshooting
  19. KenO
    Post

    Cura 3.4.1?

    What I do to set up my R2 printer in a new version of Cura is this: 1. Do not let Cura delete your copy of Cura version 2.5.0 2. Using...
    Post by: KenO, Nov 30, 2018 in forum: Software
  20. KenO
    Post

    Head crashing with Probe Failure error, fixed I think

    Jeff: I have used sandpaper on the BuildTak as well. When I first put it to use, there was no clue as to what the Z offset should be, so the...
    Post by: KenO, Mar 30, 2018 in forum: Troubleshooting
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2