1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I installed a new EPCOS 100k thermistor and swapped out the stock Arduino with a new Mega. It works now. The extruder thermistor now reads 25C at...
    Post by: RyeMAC3, Aug 5, 2016 in forum: Troubleshooting
  2. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I'm actually going to have a go at doing that. I'm an Arduino guy, so it should be easy to do now that I've taken a look at this board and know...
    Post by: RyeMAC3, Aug 4, 2016 in forum: Troubleshooting
  3. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Dang, that stinks. I guess I'll have to pick up a new board. Thanks for all the help.
    Post by: RyeMAC3, Aug 4, 2016 in forum: Troubleshooting
  4. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Huh, so this is weird. I swapped thermistor positions on the RAMPS board and the bed still reads 21.9C. So the new thermistor I installed is OK....
    Post by: RyeMAC3, Aug 4, 2016 in forum: Troubleshooting
  5. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    You didn't have it linked in your video. I saw the markings on the packaging when you held it up in the video and I managed to find the same one...
    Post by: RyeMAC3, Aug 4, 2016 in forum: Troubleshooting
  6. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I picked up a genuine EPCOS 100K thermistor and connected it. Right now, it's just connected but not inside the extruder. It should be reading...
    Post by: RyeMAC3, Aug 4, 2016 in forum: Troubleshooting
  7. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Thanks. Tried it. 6 still reads 90C, 60 reads 70C. I think these thermistors are crap. The resistance on all 10 in this pack is between 90-94K....
    Post by: RyeMAC3, Jul 29, 2016 in forum: Troubleshooting
  8. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Looks like I need to do something here... //===========================================================================...
    Post by: RyeMAC3, Jul 29, 2016 in forum: Troubleshooting
  9. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I bought them on Amazon....
    Post by: RyeMAC3, Jul 29, 2016 in forum: Troubleshooting
  10. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Installed a new 100K thermistor. It's reading 91 degrees at room temp. Is this a bad one? Or is there some sort of calibration required?
    Post by: RyeMAC3, Jul 29, 2016 in forum: Troubleshooting
  11. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Thanks for the help. I think I'll order them both on Amazon.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  12. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I have a feeling it didn't notice that the heat shrink tubing slid down and when I plugged it back in, the two heads shorted together.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  13. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Too late. The thermistor just had a meltdown. Look at the picture. It even melted the insulation. I heard it crackle and saw a spark when I...
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  14. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Oh, wow, just plugged the thermistor back in. It sparked, wires got red hot and melted the insulation instantly. Ok, so where does one get a new...
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  15. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    It's reading 82K.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  16. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    Yes, the only way to get the rubber boot off was to disconnect the wires at the disconnects and move them out the way.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  17. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    It's an R1. All original stock. Weird, where did my picture go? ....I'll attach again....looks like it says "hexagon" on the extruder.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  18. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    I took that rubber boot off. Man, what a mess it was under there. I guess 1.5 years worth of crumbly bits. So I found the heater and the...
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  19. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    It's an R1. All original stock. No modifications. About 1.5 years old.
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
  20. RyeMAC3
    Post

    Solved Anyone know what this hardware error pop up means?

    How do you check the thermistor? Where is it? And what does a "bad" one look like?
    Post by: RyeMAC3, Jul 27, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2