1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Ben Allgor
    Post

    Partial Answer Hotend Turns off after autolevel

    Oops! I I need to stay up to date.
    Post by: Ben Allgor, Aug 11, 2017 in forum: Troubleshooting
  2. Ben Allgor
    Post

    Partial Answer Hotend Turns off after autolevel

    If you are talking about the thermistor you should have a glass bead that is held in by a screw on the wires or a hex head screw with the wires...
    Post by: Ben Allgor, Aug 10, 2017 in forum: Troubleshooting
  3. Ben Allgor
    Post

    Solved extruder heats up but then 2-3 layers in to a print the temperature drops like a rock

    For what it is worth, I had a similar problem when I installed the e3d. I added the duct for the fan, but it didn't fix it. I finally fixed it...
    Post by: Ben Allgor, Jun 3, 2016 in forum: Troubleshooting
  4. Ben Allgor
    Post

    Solved Petg jams after a few hours in r1+

    If anyone needs it, you can get the tubing for 1.75 mm from Amazon. It is about $8 for a coil....
    Post by: Ben Allgor, Feb 26, 2016 in forum: General Questions
  5. Ben Allgor
    Thread

    Hot End Disaster Cured in only 2 months or so

    I got my Robo 3d last summer, and printed all kinds of things with PLA. I printed 3D nameplates (photo below) for almost everyone in the family....
    Thread by: Ben Allgor, Feb 3, 2016, 1 replies, in forum: Mods and Upgrades
  6. Ben Allgor
    Post

    Changing nozzle on hexagon hotend

    I think I got it backwards. With the heat break, and it was a bad idea anyway. The heat break would be loose in the heat Sink. Sent from my...
    Post by: Ben Allgor, Feb 3, 2016 in forum: General Questions
  7. Ben Allgor
    Post

    Changing nozzle on hexagon hotend

    Maybe you can turn the heat break little farther into the heat sink. Can you modify the shrouds by blocking part of the opening and cutting larger...
    Post by: Ben Allgor, Feb 3, 2016 in forum: General Questions
  8. Ben Allgor
    Post

    Changing nozzle on hexagon hotend

    I am sorry. The Z was an accident. Don't know how I did it. Sent from my iPhone using Tapatalk
    Post by: Ben Allgor, Feb 3, 2016 in forum: General Questions
  9. Ben Allgor
    Post

    Changing nozzle on hexagon hotend

    Z Sent from my iPhone using Tapatalk
    Post by: Ben Allgor, Feb 3, 2016 in forum: General Questions
  10. Ben Allgor
    Post

    Changing nozzle on hexagon hotend

    Nozzle must seat against heat break . Turn nozzle all the way in when cold, and back out 1/2 turn . Then heat to 260C and tighten nozzle. Some...
    Post by: Ben Allgor, Feb 3, 2016 in forum: General Questions
  11. Ben Allgor
    Post

    Rewiring limit switches

    I have been able to get the female spade connectors in most sizes at a hardware store. Some times they are better priced than the big box stores....
    Post by: Ben Allgor, Jan 31, 2016 in forum: Mods and Upgrades
  12. Ben Allgor
    Thread

    Solved Will PLA Clog a Stainless Steel Nozzle?

    Does anyone know if PLA will clog in a stainless steel nozzle like it does brass? I just started using the nozzle, and now I am wondering if I...
    Thread by: Ben Allgor, Jan 2, 2016, 7 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again