1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. momoe
    Thread

    Solved Y-axis belt with connectors

    where is a good source to buy parts for this old R1? my connector that holds the Y-axis belt to the bed rails broke off today.. I went on Robo3d...
    Thread by: momoe, Jan 4, 2020, 5 replies, in forum: Troubleshooting
  2. momoe
    Thread

    Solved Heat sink mounting issues

    Hi all. Need help. I dusted off the old printer (robo 3D R1)and am reassembling it after some time. I had to replace the whole hot end from the...
    Thread by: momoe, Dec 26, 2019, 16 replies, in forum: Troubleshooting
  3. momoe
    Thread

    Screw size needes

    Can someone tell me what size and thread the screws are that hold the heat sink in the carriage? I know it’s metric but not sure the thread or...
    Thread by: momoe, Nov 18, 2018, 4 replies, in forum: General Questions
  4. momoe
    Thread

    need new parts

    Anyone know if there is a catalog online where we can look up the parts of the base unit? I have an R1 from back in the day and I need the piece...
    Thread by: momoe, Nov 7, 2018, 7 replies, in forum: Mods and Upgrades
  5. momoe
    Thread

    Unresolved Temp error help

    I am getting a max temp error out of the blue. can anyone help me sleuth this out? from Simplify3D: Connected to machine! READ: echo: External...
    Thread by: momoe, Feb 12, 2017, 2 replies, in forum: Troubleshooting
  6. momoe
    Thread

    Partial Answer Whole hot end and heatsync are loose

    so I've noticed the whole hot end is loose. It is seated up in the carrier all the way and the screws are all the way in but they won't get tight...
    Thread by: momoe, Feb 6, 2017, 1 replies, in forum: Troubleshooting
  7. momoe
    Thread

    External PID controller for extruder heating?

    I need to have a thermocoupler because the thermisters I have keep breaking. It's killing me when I try to print T-Glase and it shuts down...
    Thread by: momoe, Jan 30, 2017, 12 replies, in forum: Mods and Upgrades
  8. momoe
    Thread

    Unresolved EXTRUDER GEAR AND MOTOR GRINDING

    Anyone want to take a shot? When extruding, my main gear or motor, not sure which, is making a buzzing/grinding noise. This causes the gears to...
    Thread by: momoe, Sep 20, 2016, 9 replies, in forum: Troubleshooting
  9. momoe
    Thread

    Feeling frustrated by the store

    so I ordered a new print bed a week and a half ago. The nice lady on the phone said its 2 day shipping and I should have got it last Monday. On...
    Thread by: momoe, Aug 28, 2016, 3 replies, in forum: Off Topic
  10. momoe
    Thread

    Solved lead screw upgrade not working

    Hello all. I just did the lead screw upgrade and the firmware upgrade but it isn't working. I think. it sounds like the lead screws are...
    Thread by: momoe, May 27, 2016, 32 replies, in forum: Troubleshooting
  11. momoe
    Thread

    Is Prototype quality possible?

    hi everyone. I'm running an R1 with a E3d volcano head and a .4 nozzle and I'm trying to do some prototype printing. I use PLA at the moment...
    Thread by: momoe, May 19, 2016, 26 replies, in forum: General Questions
  12. momoe
    Thread

    Answered Here we go again with temp issues

    Ok, so I have replaced 3 thermistors now. I am still getting this error code. I am trying to print at 205C and it starts there just fine. it...
    Thread by: momoe, May 3, 2016, 7 replies, in forum: Troubleshooting
  13. momoe
    Thread

    Answered thermocoupler issues

    running a R1 and simplify 3D Just installed a thermocoupler that is rated to 300C and I'm trying to print at 205. it will start the print and...
    Thread by: momoe, Apr 27, 2016, 4 replies, in forum: Troubleshooting
  14. momoe
    Thread

    Unanswered quality settings?

    Hi all, I am trying to print a prototype amd need th ebest quality I can manage. I have a R1 with an E3d V6 volcano with a .4mm nozzzle. I am...
    Thread by: momoe, Apr 18, 2016, 0 replies, in forum: Troubleshooting
  15. momoe
    Thread

    what material would you use?

    I am going to make a prototype mold with my #d printer to be used in an injection printer. I am thinking of using the Taulman 618 Nylon since it...
    Thread by: momoe, Apr 6, 2016, 9 replies, in forum: General Questions
  16. momoe
    Thread

    Partial Answer Building supports for items

    Does anyone routinly build supports in their 3D design program? Sclic3r is just not doing it like I want to. any advise you can provide on how...
    Thread by: momoe, Feb 1, 2016, 8 replies, in forum: General Questions
Showing results 1 to 16 of 16
Search Again