1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. GucasLuthrie
    Post

    Unresolved Sporadic Gear Movement Robo3D

    I tried what you suggested and the printer is still doing the same thing.
    Post by: GucasLuthrie, May 28, 2017 in forum: Troubleshooting
  2. GucasLuthrie
    Thread

    Unresolved Sporadic Gear Movement Robo3D

    Yesterday my 3d printer quick extruding, the gear will work for short periods of time than stop entirely. Any help would be greatly appreciated....
    Thread by: GucasLuthrie, May 28, 2017, 6 replies, in forum: Troubleshooting
  3. GucasLuthrie
    Post

    Unresolved A few quick questions

    apperently its extruding while moving over gaps? take a look[IMG] [IMG]
    Post by: GucasLuthrie, Aug 26, 2016 in forum: Troubleshooting
  4. GucasLuthrie
    Post

    Unresolved A few quick questions

    I have done that already btw :)
    Post by: GucasLuthrie, Aug 25, 2016 in forum: Troubleshooting
  5. GucasLuthrie
    Post

    Unresolved A few quick questions

    Im using Im using Hatchbox PLA Mattercontrol between 190 and 200 for the extruder and 50 for the bed I have similar results between .3mm and .1mm...
    Post by: GucasLuthrie, Aug 25, 2016 in forum: Troubleshooting
  6. GucasLuthrie
    Thread

    Unresolved A few quick questions

    Hey guys I have a small handful of questions. First off I know that bridging is hard but whenever I i print the slightest overhang it droops and...
    Thread by: GucasLuthrie, Aug 25, 2016, 15 replies, in forum: Troubleshooting
  7. GucasLuthrie
    Post

    Unanswered First layer prints with gaps

    What about the gaps between walls? [IMG]
    Post by: GucasLuthrie, Jun 10, 2016 in forum: Troubleshooting
  8. GucasLuthrie
    Post

    Unanswered First layer prints with gaps

    Any ideas?
    Post by: GucasLuthrie, Jun 10, 2016 in forum: Troubleshooting
  9. GucasLuthrie
    Post

    Unanswered First layer prints with gaps

    I followed the tutorial and it looks the same[IMG]
    Post by: GucasLuthrie, Jun 9, 2016 in forum: Troubleshooting
  10. GucasLuthrie
    Thread

    Unanswered First layer prints with gaps

    So my first layer prints with gaps. Thanks Lucas [IMG]
    Thread by: GucasLuthrie, Jun 4, 2016, 7 replies, in forum: Troubleshooting
  11. GucasLuthrie
    Post

    Unanswered Layers missing on prints

    Its a Robo3D R1 with matter control and the filament that it comes with.
    Post by: GucasLuthrie, May 13, 2016 in forum: Troubleshooting
  12. GucasLuthrie
    Post

    Unanswered Layers missing on prints

    Oops, the image didnt upload. This is it.
    Post by: GucasLuthrie, May 13, 2016 in forum: Troubleshooting
  13. GucasLuthrie
    Thread

    Unanswered Layers missing on prints

    Hey, so I printed this on high settings with PLA and there are occasionally layers missing. I was wondering if anyone had any tips on how to fix...
    Thread by: GucasLuthrie, May 13, 2016, 5 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again