1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. John M. Fruits
    Thread

    Banding Fix for Robo R2

    A while back, I posted an issue with my Robo R2 where I had severe banding on all of my prints. I had a bent Z Axis Rod, which Robo replaced free...
    Thread by: John M. Fruits, Apr 14, 2019, 3 replies, in forum: Troubleshooting
  2. John M. Fruits
    Post

    X and Y Ringing on prints - possible solutions

    Yes, more so up and down, but there is a little osculation as well. here is a short video of the movement before the spacer was printed and...
    Post by: John M. Fruits, Jun 15, 2017 in forum: Troubleshooting
  3. John M. Fruits
    Post

    R2 Bed Temp

    So, How did you get it past 80°c? I can set it to 90°, but it will top at at 80° Sent from my iPhone using Tapatalk
    Post by: John M. Fruits, Jun 12, 2017 in forum: Troubleshooting
  4. John M. Fruits
    Post

    X and Y Ringing on prints - possible solutions

    For now....I made this and inserted it under the stepper motor....[IMG] Sent from my iPhone using Tapatalk
    Post by: John M. Fruits, Jun 11, 2017 in forum: Troubleshooting
  5. John M. Fruits
    Post

    X and Y Ringing on prints - possible solutions

    The "Z" axis bearing rods are just glued into the plastic bottom support bracket (the same one that holds the stepper motor). There was a molded...
    Post by: John M. Fruits, Jun 11, 2017 in forum: Troubleshooting
  6. John M. Fruits
    Post

    X and Y Ringing on prints - possible solutions

    I had severe ringing on my prints. I found the issue. There are two issues. First, my Z Axis rod has a warp to it, which causes it to bind...
    Post by: John M. Fruits, Jun 10, 2017 in forum: Troubleshooting
  7. John M. Fruits
    Post

    Problems Encountered with my C2

    The noise while homing is due to the rods (going from the left to the right) are not hitting the limit switch. These rods are easily moved back...
    Post by: John M. Fruits, Feb 21, 2017 in forum: Troubleshooting
  8. John M. Fruits
    Post

    C2 / Auto-level

    FYI: I had an issue where the Extruder was bobbling up and down, and it was actually one of the bearings at the top (X Axis).... It had popped...
    Post by: John M. Fruits, Feb 21, 2017 in forum: Show and Tell
  9. John M. Fruits
    Post

    Cura for Mac install......

    Solved! ..... This is for Cura 2.3.1 Step 1) Download the following plugin. https://github.com/fieldofview/OctoPrintPlugin Step 2) Go to your...
    Post by: John M. Fruits, Feb 18, 2017 in forum: Software
  10. John M. Fruits
    Thread

    Cura for Mac install......

    Finally, Robo put the instructions on the software page to install Cura for the Mac. The setup was fairly simple, and it is now installed....
    Thread by: John M. Fruits, Feb 18, 2017, 5 replies, in forum: Software
  11. John M. Fruits
    Post

    Prints are not round......

    Solved my out of round issue. I ordered two additional printers, and when one came in, the X axis (From left to Right) was not parallel with...
    Post by: John M. Fruits, Feb 12, 2017 in forum: Show and Tell
  12. John M. Fruits
    Thread

    Print Adhesion

    Just thought I would share what is working for me..... I have two Robo C2's, running Build-Tak stickers on the build plate. They do not...
    Thread by: John M. Fruits, Feb 6, 2017, 7 replies, in forum: Show and Tell
  13. John M. Fruits
    Post

    Prints are not round......

    Checked the belts and they are all banjo tight!
    Post by: John M. Fruits, Feb 6, 2017 in forum: Show and Tell
  14. John M. Fruits
    Post

    macOS Software

    Thanks!
    Post by: John M. Fruits, Feb 3, 2017 in forum: Troubleshooting
  15. John M. Fruits
    Post

    macOS Software

    Cory, would you be so kind as to explain with a little more detail? I have no idea what "get hub" is.... Sorry.
    Post by: John M. Fruits, Feb 3, 2017 in forum: Troubleshooting
  16. John M. Fruits
    Post

    Cura on Windows....

    Thanks to Cory, I figured it out. You need to copy your API key from within Octoprint and paste it in the Cura printer settings. 1. Browse to...
    Post by: John M. Fruits, Feb 3, 2017 in forum: Software
  17. John M. Fruits
    Thread

    Cura on Windows....

    I've installed the Cura software for Windows, and I have connected the printer, but when I go to send the code file directly to the printer, it...
    Thread by: John M. Fruits, Feb 3, 2017, 6 replies, in forum: Software
  18. John M. Fruits
    Post

    Prints are not round......

    Photo...
    Post by: John M. Fruits, Feb 3, 2017 in forum: Show and Tell
  19. John M. Fruits
    Thread

    Prints are not round......

    Love the printer, but there are a few quirks to be hashed out....and I am confident they will be! But, when I print a round "wheel", the wheel...
    Thread by: John M. Fruits, Feb 3, 2017, 5 replies, in forum: Show and Tell
  20. John M. Fruits
    Post

    Solved Touch Screen Sensitivity

    I took my display out as the black front bezel just snaps on.... And put some non conductive shims behind the display. After the bezel is...
    Post by: John M. Fruits, Feb 3, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 36 Next >
Search Again
Page 1 of 2