1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Drakeh
    Post

    E3D v6 Information, Installation Guides, and Review

    Thanks mark that might be my problem.
    Post by: Drakeh, Jul 28, 2016 in forum: Mods and Upgrades
  2. Drakeh
    Post

    E3D v6 Information, Installation Guides, and Review

    Not sure if this makes a difference but I noticed that the first time I purchased my E3D I got a 12v heater cartridge and this time it seems I...
    Post by: Drakeh, Jul 28, 2016 in forum: Mods and Upgrades
  3. Drakeh
    Post

    E3D v6 Information, Installation Guides, and Review

    Hey Josh, Thanks again for your help. Where exactly in the firmware would I find the thermistor type? I tried to search for thermistor but it...
    Post by: Drakeh, Jul 28, 2016 in forum: Mods and Upgrades
  4. Drakeh
    Post

    E3D v6 Information, Installation Guides, and Review

    What I mean by my thermistor came out is that the little wires for the thermistor pulled out of the little ferrules that hold them to the other...
    Post by: Drakeh, Jul 28, 2016 in forum: Mods and Upgrades
  5. Drakeh
    Post

    E3D v6 Information, Installation Guides, and Review

    Hey guys, so I've been using my E3D V6 on my Robo 3D for quite a while now and I love it, but recently my thermistor came out of the hotend and I...
    Post by: Drakeh, Jul 27, 2016 in forum: Mods and Upgrades
  6. Drakeh
    Thread

    Solved Temp shows over 600

    So my E3D V6 hotend recently broke so I had to order a new one. They started using a new thermistor cartridge so I hooked everything up to my...
    Thread by: Drakeh, Jul 27, 2016, 2 replies, in forum: Troubleshooting
  7. Drakeh
    Post

    Solved Printer homing is messed up!

    Hey Mark. It was one of the endstop connectors and I was able to figure out where it went because the connector pins were bent. It must have...
    Post by: Drakeh, Feb 10, 2016 in forum: Troubleshooting
  8. Drakeh
    Post

    Solved Printer homing is messed up!

    Hey Mark so I flipped the connector for the y-axis motor and that fixed it perfectly. My x-axis is still doing weird things so I opened up the...
    Post by: Drakeh, Feb 10, 2016 in forum: Troubleshooting
  9. Drakeh
    Post

    Solved Printer homing is messed up!

    Is that a matter of opening up the bottom and flipping the connecter 180 degrees?
    Post by: Drakeh, Feb 9, 2016 in forum: Troubleshooting
  10. Drakeh
    Post

    Solved Printer homing is messed up!

    Another thing that probably would be good to know is that I am using Simplify3D on my iMac currently
    Post by: Drakeh, Feb 9, 2016 in forum: Troubleshooting
  11. Drakeh
    Thread

    Solved Printer homing is messed up!

    Hey guys, so I haven't used my printer in a while because one of the wires for the stepper motor came out of the piece to attach it to the motor...
    Thread by: Drakeh, Feb 9, 2016, 7 replies, in forum: Troubleshooting
Showing results 1 to 11 of 11
Search Again