1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    Pulled the extruder stepper and the X stepper and the extruder one feels just a hair rougher then the X one, The biggest thing I noticed comparing...
    Post by: Nomad83, Feb 15, 2017 in forum: Troubleshooting
  2. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    Any or all of them. I did notice now that I think of it the extruder one got stuck a few times. Went to manually turn the extruder and it was...
    Post by: Nomad83, Feb 9, 2017 in forum: Troubleshooting
  3. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    How would I test for that?
    Post by: Nomad83, Feb 8, 2017 in forum: Troubleshooting
  4. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    I just broke out the Yellow to test that idea a few days ago. Weirdly I got bored today and tried attaching a fan with ducting i made a few weeks...
    Post by: Nomad83, Feb 8, 2017 in forum: Troubleshooting
  5. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    I may branch back into PLA at some point once the bugs here are found. But it just irks me to no end that I used to be able to print at least...
    Post by: Nomad83, Feb 8, 2017 in forum: Troubleshooting
  6. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    Oh and I don't think it matters but just to make sure. I'm not running any cooling fans.
    Post by: Nomad83, Feb 6, 2017 in forum: Troubleshooting
  7. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    I did a fresh install of MC on my desktop and after tweaking the z lift so it prints instead of dragging the tip on the glass it still has some...
    Post by: Nomad83, Feb 6, 2017 in forum: Troubleshooting
  8. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    Should tweaking the extruder down a bit for quick and dirty testing work? I have a caliper around here somewhere but haven't found it yet. So I...
    Post by: Nomad83, Feb 4, 2017 in forum: Troubleshooting
  9. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    No Ideas? Tried to print a spool holder and the print failed every time. [IMG] [IMG] Any ideas as to whats causing this? Or what to try?...
    Post by: Nomad83, Jan 31, 2017 in forum: Troubleshooting
  10. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    The bottom is flat as the glass. X is front face Y is the right face Z is the top face As observed from the front.
    Post by: Nomad83, Jan 25, 2017 in forum: Troubleshooting
  11. Nomad83
    Post

    Unresolved Print issues while getting r1 up and running

    Sorry it was 3am. Lol Abs 240c 80c bed Matter control with no tweaks.
    Post by: Nomad83, Jan 25, 2017 in forum: Troubleshooting
  12. Nomad83
    Thread

    Unresolved Print issues while getting r1 up and running

    Finally moved somewhere I can use my printer again. Fixed a broken belt clip on the belt but figured I should try some calibration since it was...
    Thread by: Nomad83, Jan 25, 2017, 19 replies, in forum: Troubleshooting
  13. Nomad83
    Post

    Unanswered Print starts out great then falls apart.

    I totally forgot about that fan since I misplaced my bottom cover with attached fan during my divorce. Frustrating part now is findingredients a...
    Post by: Nomad83, Sep 1, 2016 in forum: Troubleshooting
  14. Nomad83
    Thread

    Unanswered Print starts out great then falls apart.

    I figure this is probably something stupid but I've been beating my head against the wall. Just upgraded to E3D V6 and it runs amazing at first...
    Thread by: Nomad83, Sep 1, 2016, 4 replies, in forum: Troubleshooting
  15. Nomad83
    Post

    Unresolved Replaced the Bed and now issues.

    Well that wont be possible since the old hot end snapped trying to take it apart to clean.
    Post by: Nomad83, Aug 25, 2016 in forum: Troubleshooting
  16. Nomad83
    Post

    Unresolved Replaced the Bed and now issues.

    No but I dont think it is. If i can find my nice ground flat level I'll check that. I think i figure out one issue with the hexagon head leaking...
    Post by: Nomad83, Aug 24, 2016 in forum: Troubleshooting
  17. Nomad83
    Thread

    Unresolved Replaced the Bed and now issues.

    I finally got a replacement bed after my old one was shattered. Got the magnets glued on which I was not thrilled to have to DIY but it seemed to...
    Thread by: Nomad83, Aug 24, 2016, 6 replies, in forum: Troubleshooting
  18. Nomad83
    Post

    Answered Print bed shattered.

    Well thats some good new at least. Just wished I had come here first I guess rather than wasting time with chatra or the facebook page....
    Post by: Nomad83, Jun 27, 2016 in forum: Troubleshooting
  19. Nomad83
    Post

    Answered Print bed shattered.

    Looks like they are all sold out.
    Post by: Nomad83, Jun 27, 2016 in forum: Troubleshooting
  20. Nomad83
    Thread

    Answered Print bed shattered.

    Well about a month ago my print bed shattered and I started trying to find a replacement. I was going to order from the parts list after a payday...
    Thread by: Nomad83, Jun 26, 2016, 11 replies, in forum: Troubleshooting
Showing results 1 to 20 of 20
Search Again