1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Bil Forshey
    Post

    First test of FLEKS 3D build plate kit

    The bed is 10" in the X axis so the 10 X 10" frame will just fit the X. You will loose about 1" of build area on the Y axis though. The next best...
    Post by: Bil Forshey, Mar 25, 2016 in forum: Show and Tell
  2. Bil Forshey
    Post

    Have I missed any modifications to my Robo R1+?

    ABS should stick very well. Check your Z height to make sure it is set correctly. Make sure you are printing on the rough side of the build...
    Post by: Bil Forshey, Mar 23, 2016 in forum: Show and Tell
  3. Bil Forshey
    Post

    Unanswered Err: MINTEMP

    I unplugged my thermistor yesterday while readjusting my hot end and my display showed "Err MINTEMP" so it means the Ramps can't read your...
    Post by: Bil Forshey, Mar 16, 2016 in forum: Troubleshooting
  4. Bil Forshey
    Post

    First test of FLEKS 3D build plate kit

    Here's what I did, I mounted the frame to the glass bed (centered) with 1/2" wide Scotch double sided transparent tape applied to the rough side...
    Post by: Bil Forshey, Mar 14, 2016 in forum: Show and Tell
  5. Bil Forshey
    Post

    Solved Cleaning the bed

    If you would like to never have to clean your glass bed again and not have to use hairspray, glue sticks, tape, or even worry about your prints...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Troubleshooting
  6. Bil Forshey
    Post

    Experimenting with filament colorizing

    I bought the Makerbot Rep 2 5th gen model it is a little too small I think I would get the 10" x !0" for a better fit. I emailed Fleks3D and...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  7. Bil Forshey
    Post

    hair spray tip for stick

    PLA and ABS were the only choices when us "old timers" started with our first 3D printers. I use Taulman N-Vent a lot now, but there so many more...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  8. Bil Forshey
    Post

    Experimenting with filament colorizing

    My Robo R1_Filament_Colorizer is up on Thingiverse now, If anyone wants to try it. http://www.thingiverse.com/thing:1412902
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  9. Bil Forshey
    Post

    hair spray tip for stick

    Before I got the Fleks 3D build plate I could never get anything that large to stick long enough to successfully print, of course I was using ABS,...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  10. Bil Forshey
    Post

    hair spray tip for stick

    10 x 10 should be good for them i think. Check with FLEKS3D if you have questions.
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  11. Bil Forshey
    Post

    hair spray tip for stick

    I believe the 10 x 10 inch (254mm x 254mm) size should fit on the Robo's bed. If they get enough requests they may make a size just for the Robo...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  12. Bil Forshey
    Post

    Solved xxl control going bananas

    This is a common problem with the XXL LCD, I had the same problem with mine from the start, the cause is electrical noise induced through the...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Troubleshooting
  13. Bil Forshey
    Post

    hair spray tip for stick

    No more hairspray for me! I would highly recommend the FLEKS 3D build plate for any 3D printer users, It eliminates the most aggravating problem...
    Post by: Bil Forshey, Mar 13, 2016 in forum: Show and Tell
  14. Bil Forshey
    Post

    Have I missed any modifications to my Robo R1+?

    Thanks for the reply, I agree with your comments. The bed heater is now a non-issue for me as the FLEKS3D build plate system doesn't require...
    Post by: Bil Forshey, Mar 12, 2016 in forum: Show and Tell
  15. Bil Forshey
    Post

    Partially Solved m3 stud thermistor

    Check to see if the extruder temperature setting in your slicer is set properly, and that it is turned on again after the start gcode in...
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
  16. Bil Forshey
    Post

    Unresolved Filament stuck

    Check out this video. [MEDIA]
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
  17. Bil Forshey
    Post

    Unresolved Removing Extruder Assembly

    Check out this video [MEDIA] Ball bearings should not be falling out! Call Robo 3D tech support for help 844-476-2633 they are available 24/7...
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
  18. Bil Forshey
    Post

    Unanswered First print Help!

    Check the printer settings in the Mattercontrol software, you can set all of the print bed parameters there.
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
  19. Bil Forshey
    Post

    Solved Faulty Extruder Stepper Motor?

    Check to see if there is a loose wire on the connector for the extruder motor near the printhead, sometimes the connectors are not crimped...
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
  20. Bil Forshey
    Post

    Unanswered Xxl screen shows sleep?

    It is possible that your gcode contains a Pause command, try using the menu to enter a resume print command. M226: Gcode Initiated Pause...
    Post by: Bil Forshey, Mar 12, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2