1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. ballhogjoni
    Thread

    Popping sound?

    My printer is making a popping sound when it travels on the X axis. I can't pinpoint the exact location of the sound. I'm not sure if it's gears...
    Thread by: ballhogjoni, Feb 9, 2022, 1 replies, in forum: Troubleshooting
  2. ballhogjoni
    Thread

    Auto Bed Leveling?

    My auto bed leveling doesn't seem to work. The printer goes through the motions of auto bed leveling before each print, but the bed is just a...
    Thread by: ballhogjoni, Feb 18, 2021, 3 replies, in forum: General Questions
  3. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    I had to reset my firmware to the initial production configuration of Marlin for R2 of 1.1.7. https://github.com/Robo3D/Marlin/releases/tag/1.1.7
    Post by: ballhogjoni, Apr 1, 2020 in forum: Troubleshooting
  4. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    I also downloaded it and still same issue.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  5. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Attempting from URL...is alerts me that flashing was successful.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  6. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Yes
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  7. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Print finished and then I flashed. It was idle.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  8. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Tried the z offset wizard and same problem is happening.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  9. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Flash from url https://github.com/Robo3D/Marlin/releases/download/Marlin_1.1.6_RoboVersion_1.2.6/Marlin_1.1.6_RoboVersion_1.2.6_R2.hex did not work.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  10. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Is there a way to back up the firmware before updating? I manually set the z-offset and I'm in the middle of a print so at least I can manually...
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  11. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    Thanks I see this post and i think it'll fix...will post updates.
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  12. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    When I go to update from the touchscreen it says RoboOs 2.0.0-r2.6 is installed
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  13. ballhogjoni
    Post

    Z-Offset Wizard stuck at step 1 of 4

    FIRMWARE_NAME:Marlin Marlin_1.1.6_RoboVersion_1.2.4 Robo R2 SOURCE_CODE_URL:https://github.com/Robo3D/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:...
    Post by: ballhogjoni, Mar 24, 2020 in forum: Troubleshooting
  14. ballhogjoni
    Thread

    Z-Offset Wizard stuck at step 1 of 4

    See picture. It's been like this for 10 minutes or more.
    Thread by: ballhogjoni, Mar 24, 2020, 63 replies, in forum: Troubleshooting
  15. ballhogjoni
    Post

    Error When Heating the Bed and Hotend

    Thanks Kilrah I have it set at 80 because that was the suggested temp for the STL i'm trying to print. I will try and have it preheated for a...
    Post by: ballhogjoni, Jul 2, 2017 in forum: Troubleshooting
  16. ballhogjoni
    Post

    Error When Heating the Bed and Hotend

    I didn't write down the error. It just mentioned that it was disconnecting and shutting down. The R2 just stops in its tracks.
    Post by: ballhogjoni, Jul 1, 2017 in forum: Troubleshooting
  17. ballhogjoni
    Thread

    Error When Heating the Bed and Hotend

    I'm trying to print some glow in the dark ABS but I keep running into an error that shuts down the connection with OctoPrint. This shutdown tops...
    Thread by: ballhogjoni, Jul 1, 2017, 4 replies, in forum: Troubleshooting
  18. ballhogjoni
    Thread

    R2 not reading USB drive

    I've added some new STL files to the USB drive that came with the printer but I plug it in and it doesn't read the files. What have I done wrong?...
    Thread by: ballhogjoni, Jun 21, 2017, 24 replies, in forum: Troubleshooting
  19. ballhogjoni
    Post

    Screen unresponsive?

    I've thought the same thing but I've waited over 10 minutes...so that can't be a lag issue or at least i'd hope they would have put a faster...
    Post by: ballhogjoni, Jun 20, 2017 in forum: Troubleshooting
  20. ballhogjoni
    Thread

    Screen unresponsive?

    I've contacted support with no answer that has worked. My screen only responds to finger touch and stylus touch about 5% of the time. I've turned...
    Thread by: ballhogjoni, Jun 20, 2017, 8 replies, in forum: Troubleshooting
Showing results 1 to 20 of 34 Next >
Search Again
Page 1 of 2