1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. John Huggins
    Thread

    Unanswered Bed leveling question

    I do have another question about the bed leveling. I am printing on a PEI surface and have checked the bed with a level. I have done the basic...
    Thread by: John Huggins, Oct 12, 2016, 2 replies, in forum: General Questions
  2. John Huggins
    Post

    Solved Stainless steel print nozzles

    Thanks to all for your answers, and Thanks Waldo for your explanation about stainless steel nozzles. I was looking at them for the wrong reasons,...
    Post by: John Huggins, Oct 12, 2016 in forum: General Questions
  3. John Huggins
    Post

    Solved Stainless steel print nozzles

    Thanks, I will keep that in mind if I try them. Where do you get your hardened nozzles and what size do you use for the majrity of your prints?
    Post by: John Huggins, Oct 11, 2016 in forum: General Questions
  4. John Huggins
    Thread

    Solved Stainless steel print nozzles

    Has anyone tried using a stainless steel nozzle on a Robo3D R1+ as a replacement for the brass nozzle. If so any changes or adjustments that need...
    Thread by: John Huggins, Oct 11, 2016, 12 replies, in forum: General Questions
  5. John Huggins
    Post

    Unanswered PEI print bed help

    Thanks, I will give it a try.
    Post by: John Huggins, May 10, 2016 in forum: General Questions
  6. John Huggins
    Post

    Solved Warping using ABS, please advise.

    I print ABS almost all the time. I have the bed at 90C and 230C for the hot end and no fan on the part at all. ABS does not like a cooling fan at...
    Post by: John Huggins, May 4, 2016 in forum: General Questions
  7. John Huggins
    Thread

    Unanswered PEI print bed help

    I just added a PEI print bed. So far, I can't get anything to stick to it like the reviews say. Any suggestions as to what settings to change and...
    Thread by: John Huggins, May 3, 2016, 3 replies, in forum: General Questions
  8. John Huggins
    Post

    Robo3D R1 upgrades and updates

    The Winged Victory was the first large piece I tried when I first got the printer. Lots of ribbing problems that have been resolved. The last pic...
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  9. John Huggins
    Post

    Robo3D R1 upgrades and updates

    Here are some pics of the printer mods
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  10. John Huggins
    Post

    Robo3D R1 upgrades and updates

    Here is Vinus [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]...
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  11. John Huggins
    Post

    Robo3D R1 upgrades and updates

    Go to http://imgur.com/a/CKOmK to see pics of the printer upgrades and http://imgur.com/a/JkoSY to see pics of Vinus and the Winged Victory. The...
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  12. John Huggins
    Post

    Robo3D R1 upgrades and updates

    The 60mm fan adapter is now a thing. number 1446583. Enjoy
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  13. John Huggins
    Post

    fan specs for hexagon hot-end?

    Done, Thing 1446583 enjoy
    Post by: John Huggins, Mar 27, 2016 in forum: General Questions
  14. John Huggins
    Post

    Robo3D R1 upgrades and updates

    Point me to a place to drop the pics and I will put them in. Thanks.
    Post by: John Huggins, Mar 27, 2016 in forum: Show and Tell
  15. John Huggins
    Thread

    Robo3D R1 upgrades and updates

    I got my R1 last May, and have been using it almost nonstop since. Initially I had some issues with it. Bad ribbing, it would not print large item...
    Thread by: John Huggins, Mar 27, 2016, 10 replies, in forum: Show and Tell
  16. John Huggins
    Post

    fan specs for hexagon hot-end?

    If anyone is still interested, I just printed the 30mm hex adapter and then took a 30 to 40mm adapter and reduced the z height to 5mm when I...
    Post by: John Huggins, Mar 27, 2016 in forum: General Questions
  17. John Huggins
    Post

    Solved ABS on with the factory hex hotend?

    I print ABS Almost all the time at 235 and 90 with no problems. Again, the biggest problem with ABS is keeping the environment stable.
    Post by: John Huggins, Mar 20, 2016 in forum: General Questions
  18. John Huggins
    Profile Post

    Good evening Harry, I was looking at my profile and notices that my birth date is incorrect. I...

    Good evening Harry, I was looking at my profile and notices that my birth date is incorrect. I know it is a little thing, but when you have the...
    Profile post by John Huggins for Harry, Mar 19, 2016
  19. John Huggins
    Post

    Solved Upgrading to new quick release

    Worked like a charm. Printed the E3D plate a 4.2mm thickness and it fit like a glove. The only thing that has to change are the two mounting...
    Post by: John Huggins, Mar 19, 2016 in forum: General Questions
  20. John Huggins
    Thread

    Solved Upgrading to new quick release

    I have a R1 with a Hex hot end. Is it possible to upgrade to the new quick release system by just printing out the plate, removing the top of the...
    Thread by: John Huggins, Mar 18, 2016, 2 replies, in forum: General Questions
Showing results 1 to 20 of 20
Search Again